Installation XB2-Kit: Unterschied zwischen den Versionen
Aus KeyboardPartner Wiki
Zur Navigation springenZur Suche springen
Bovist (Diskussion | Beiträge) K (Schützte „Installation XB2-Kit“ ([edit=sysop] (unbeschränkt) [move=sysop] (unbeschränkt))) |
Bovist (Diskussion | Beiträge) |
||
| Zeile 3: | Zeile 3: | ||
(This page in english for int'l customers) | (This page in english for int'l customers) | ||
Installation in Hammond XB-2 may be performed by any skilled person; no soldering required. Please click on picture to enlarge. Please also regard Wiki HX-3 user manual on [[Bedienungshinweise#XB2-Nachrüstsatz]]. | Installation in Hammond XB-2 may be performed by any skilled person within 1 or 2 hours; no soldering required. Please click on picture to enlarge. Please also regard Wiki HX-3 user manual on [[Bedienungshinweise#XB2-Nachrüstsatz]]. | ||
For old kit (no longer produced), see here: '''[[Installation in Hammond XB-2 (old HX3 kit)]]''' Use for reference only! | For old kit (no longer produced), see here: '''[[Installation in Hammond XB-2 (old HX3 kit)]]''' Use for reference only! | ||
| Zeile 9: | Zeile 9: | ||
[[Datei:Xb2_01.JPG|640px|thumb|left|'''Open XB-2 by loosening 5 big screws on bottom. Remove keyboard by loosening 7 medium sized black and brass screws on bottom and inside organ. Disconnect keyboard from mainboard plug connector. Remove nylon wire straps on cable harness, but DO NOT cut any cables, just unplug all connectors!''']] | [[Datei:Xb2_01.JPG|640px|thumb|left|'''Open XB-2 by loosening 5 big screws on bottom. Remove keyboard by loosening 7 medium sized black and brass screws on bottom and inside organ. Disconnect keyboard from mainboard plug connector. Remove nylon wire straps on cable harness, but DO NOT cut any cables, just unplug all connectors!''']] | ||
[[Datei:Xb2_02.JPG|640px|thumb|left|'''Remove all boards inside including supporting rails. Retain cables and headers from power supply, front panel, drawbars, LCD and volume/reverb pots. Locate pink/black/green/orange strain and separate black/white strain to now unused connectors. Obsolete XB-2 power connectors may be cut off as pictured or may be left open and tied up securely. Insulate cut wires with shrink tube. DO NOT cut long orange/black/green/black/yellow cable!''']] | [[Datei:Xb2_02.JPG|640px|thumb|left|'''Remove all boards inside including supporting rails. Retain cables and headers from power supply, front panel, drawbars, LCD and volume/reverb pots. Locate pink/black/green/orange strain and separate black/white strain to now unused connectors. Obsolete XB-2 power connectors may be cut off as pictured here or may be left open and tied up securely (see next picture). Insulate cut wires with shrink tube. DO NOT cut long orange/black/green/black/yellow cable!''']] | ||
[[Datei:Xb2_32.JPG|640px|thumb|left|'''Install large HX3/XB-2 mainboard as pictured using wood screws and 5mm plastic spacers supplied with kit. Connect drawbar, LCD and button cables to matching connectors on LCD interface board. Connectors are all different size and cannot be confused. Re-install keyboard and connect to 15-pin header on HX3/XB-2 mainboard (right side).''']] | [[Datei:Xb2_32.JPG|640px|thumb|left|'''Install large HX3/XB-2 mainboard as pictured using wood screws and 5mm plastic spacers supplied with kit. Connect drawbar, LCD and button cables to matching connectors on LCD interface board. Connectors are all different size and cannot be confused. Re-install keyboard and connect to 15-pin header on HX3/XB-2 mainboard (right side).''']] | ||
Version vom 7. Oktober 2013, 10:56 Uhr
Installation in Hammond XB-2
(This page in english for int'l customers)
Installation in Hammond XB-2 may be performed by any skilled person within 1 or 2 hours; no soldering required. Please click on picture to enlarge. Please also regard Wiki HX-3 user manual on Bedienungshinweise#XB2-Nachrüstsatz.
For old kit (no longer produced), see here: Installation in Hammond XB-2 (old HX3 kit) Use for reference only!
Remove all boards inside including supporting rails. Retain cables and headers from power supply, front panel, drawbars, LCD and volume/reverb pots. Locate pink/black/green/orange strain and separate black/white strain to now unused connectors. Obsolete XB-2 power connectors may be cut off as pictured here or may be left open and tied up securely (see next picture). Insulate cut wires with shrink tube. DO NOT cut long orange/black/green/black/yellow cable!
Install large HX3/XB-2 mainboard as pictured using wood screws and 5mm plastic spacers supplied with kit. Connect drawbar, LCD and button cables to matching connectors on LCD interface board. Connectors are all different size and cannot be confused. Re-install keyboard and connect to 15-pin header on HX3/XB-2 mainboard (right side).
Install new jack/preamp board board as pictured. Re-install MIDI jack board and connect to jack/preamp board's 12-pin header. Connect long orange/black/green/black/yellow cable to matching 5-pin header on jack board. Connect Leslie 11-pin connector to matching header on jack board (right side). Connect gray and red/brown/white cable connectors to matching headers on jack board. Connectors are mostly different size and cannot be confused. Connect 26-pin flat ribbon cable to HX3/XB-2 main board and jack board.
