HX3.7 Main page
HX3.7 – Preliminary Draft
Common Features with HX3.5/HX3.6
- Same firmware and same FPGA sound engine
- Same PCB size, same mounting holes
- Same location of DC, USB, audio and MIDI connectors
- MenuPanel/Preset Bus Connector (I2C)
- Analog MPX Bus for newer DBX, PTX and ANX boards
- Auxiliary MIDI out, Fatar scan and pedal scan connectors
Omitted Features
- No onboard drawbar inputs
- No onboard button/switch inputs
HX3.7 does no longer offer "legacy" button/switch inputs (like Panel16) and classic analog drawbar inputs (old DB9/DB9-MPX boards). Instead, it relies on I2C bus interfaces on external panels (like Preset16, Extern16 or VibSw) and analog scanning circuits as found on PTX, ANX, DBX9 and DBX12 drawbar boards. For existing OEM installations, we will offer an interface (LegacyBoard) providing connectors for legacy hardware (see below).
However, we strongly recommend I2C bus (PANEL I2C connector) and MPX bus (ANLG MPX, analog scanning) circuits as this greatly reduces wiring effort. Refer to our DBX, ANX and PTX schematics for MPX bus interfacing (using 74HC164 shift registers and 4066 analog switches) and Preset16/VibSw schematic (using PCA9554A and PCA9555 port devices) for I2C bus interfacing.
See HX3.7 Schematics Directory for detailed PDF drawings and schematics.
Additional Features
- All ExtensionBoard features integrated
- Integrated 11-pin Leslie control, ExtensionBoard pinout on 14-pin box header PL1
- Additional DAC, outputs for plain organ and pedal signal, total of 4 audio output channels
- Headphone amp
- Improved DACs and audio amps/filters
- Insert loop (mono effects insert between tube amp simulation and rotary simulation)
- 3 onboard MIDI connectors (2x IN, 1x OUT)
- Onboard audio output jacks may be jumpered as L/R mono jacks or stereo L/R and stereo headphone jack
- Additional output signals and effect loop input available on 16-pin box header PL2 and 3-pin wire-to-board connectors
- JackExtension PCB available for additional MIDI and audio input/output jacks, same jack location as old extension board
MIDI output jack may be mounted on mainboard (new hole for connector necessary) or custom JackExtension board (old location of MIDI OUT connector) alternatively. Note: JackExtension board may be customized for OEM use as it only contains passive components (jacks, optional level potentiometer).
See HX3.7 Schematics Directory on our Update Server for details.
| PL1 Leslie 11pin Connector | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| Pin | Funktion | ||||||||
| 1 | Rotary audio channel, to pin 1 | ||||||||
| 2, 3, 10 | Stationary audio channel, to pin 2 resp. 3 and 10 | ||||||||
| 4 | Audio ground, to pin 4 | ||||||||
| 5 | Common ground for control signals, to pin 5 | ||||||||
| 6 | Power ON (MOSFET switches positive voltage to ground), to pin 6 | ||||||||
| 7 | Fast (MOSFET switches positive voltage to ground), to pin 7 | ||||||||
| 9 | Slow/Run (MOSFET switches positive voltage to ground), to pin 8 | ||||||||
| 11 | Leslie +30V supply (clamping), to pin 11 | ||||||||
| 12 | Aditional analog Gnd output, not connected | ||||||||
| 13 | Auxiliary Gnd output for relays if needed | ||||||||
| 14 | Auxiliary +5V supply output for relays if needed | ||||||||
| PL2 Extension Jacks Connector | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| Pin | Funktion | ||||||||
| 1 | Headphone Left | ||||||||
| 2 | Headphone Right | ||||||||
| 3 | Ext Out L (plain ORGAN signal) | ||||||||
| 4 | Ext Out R (plain PEDAL signal) | ||||||||
| 5 | Ext In L (Effect Loop Input, mixed to mono) | ||||||||
| 6 | Ext In R (Effect Loop Input, mixed to mono) | ||||||||
| 7 | Sustain Footswitch | ||||||||
| 8 | Sostenuto Footswitch | ||||||||
| 9 | MIDI OUT (-, DIN pin 5) | ||||||||
| 10 | MIDI OUT (+, DIN pin 4) | ||||||||
| 11 | Efx Jack Insert Switch (open when inserted, Gnd when not) | ||||||||
| 12 | Vcc +5V | ||||||||
| 13, 14 | Analog Ground | ||||||||
| 15, 16 | Digital Ground | ||||||||
HX3.7 JackExtension
A small board will be available which makes installation of additional HX3.7 connectors easier. HX3.7 JackExtension will be used in futute 19" rack expander. It replaces the former HX3 ExtensionBoard. HX3.7 JackExtension connects to HX3.7 PL2 and only carries passive/mechanical parts for convenient wiring. For OEM applications, JackExtension may be customized to existing chassis layouts.
HX3.7 LegacyBoard
As HX3.7 does no longer offer legacy analog and switch inputs, the HX3.7 LegacyBoard will be available to connect existing passive switch/button boards like Panel16 (16 inputs) and analog drawbar controls (24 inputs). The LegacyBoard is not needed for new installations using the new MPX connector (all DBX/PTX/ANX boards). It connects to HX3.7 PL31 PANEL I2C and PL32 ANLG MPX box headers.
