HX3 MIDI expander module

HX3 Expander (prototype, front panel colour and lettering may change on production units)

PAGE UNDER CONSTRUCTION!

HX3 MIDI expander is a tonewheel organ in a small box! Controlled completely via MIDI, selectable CC-sets for NI B4, Hammond XK, Hamichord and other. 30 presets (to be stored locally), many "secret" HX3 parameters tweakable by menu with incremental encoder - like key contact flex and damping for key click response, or AO28 gain adjustments for more or less percussion punch etc. And, of course, it yields the legendary unmatched HX3 sound.

Features

• Compact organ emulator module in aluminum box, 221 x 42 x 140 mm
• Authentic reproduction of generator, tapering, key contacts, percussion and vibrato by FPGA (Field Programmable Gate Array)
• Extremely low latency of 50 microseconds Key-to-Audio (not >20 ms as with other MIDI expanders and software emulation)
• Natural key click by "rattling" contacts
• Accurate Leslie simulation with separate outputs
• MIDI IN accepts 5 different MIDI CC sets
• 7 LEDs show vibrato and percussion setting
• LCD display and menu system with 2x16 presets, virtual drawbars and parameter tuning
• Swell (expression) pedal and footswitch jacks

Kit Assembly

You will need only a phillips screwdriver to build! The HX3 expander kit comes with fully functional boards, front and rear bezel/panel, cables, screws and aluminum enclosure. Make shure you have a size 1 PH screwdriver handy, also small pliers or metric 5.5 mm wrench to holt the nuts while fastening.

• Install HX3 main board to rear panel. The 4 jack nuts hold the entire board. The 4 washers are to be installed outside of rear bezel.
• Use M3 screw, locking washer and M3 nut to fasten the voltage regulator to back panel. The voltage regulator's body should have full contact to back panel as it is used as a heat sink.
• Remove protective film from LCD just prior to final installation.
• Fasten MenuDisplay board to front panel using 6 M3 bolts with spacers. Space between board and front panel should be approx. 12 mm. Be shure not to bend LED wires.
• Fasten side panels to front panel using 4 self-tapping screws.
• Insert bottom panel into slots of side panel.
• Connect 2 flat-ribbon cables to board connectors as pictured.
• Set jumper JP6 on HX3 main board to desired operation: In position "MONO", organ main and pedal outputs are mixed to one channel on MAIN/BASS output jack (plug tip), in other position to separate channels (pedals on plug "ring", right channel).
• Be shure to remove jumper JP12 (near DC jack) when using a 9 to 12V DC power supply (default: no jumper). If you plan to use a 5V power supply, move jumper from AGND spare position to JP12. Note: Damage will occur if higher voltage than 5V applied whith JP12 installed!
• Fasten side panels to back panel using 4 self-tapping screws.
• Affix 4 self-adhesive bases to bottom panel in each corner.

You're done! Time to try out: Plug in appropriate power supply 9 to 12V 800mA min. to DC jack. Display will illuminate and show welcome message, serial number and owner information (your name per default). Turn knob to select a preset. LEDs on right side will show corresponding vibrato/percussion setting.

Jack Connections

The HX3 expander module has two "stereo" type 1/4" audio output jacks, one DC input jack and two accessory jacks on back panel.

• MAIN/BASS: Separate output for main organ manuals (plug tip) and pedal (plug ring) on jack if 3-pin jumper JP6 set to 2-CHANNEL. Use Y-cable or stereo cable to obtain all channels. Outut is mono (mix of manuals and bass) if JP6 set to MONO (only plug tip connected). Output level is approx. 150 mV at full swell.
• LESL/AMP: Leslie simulation (mono, plug tip) and leslie amp simulation (122 amp without speakers, but with overdrive capabilities, plug ring). Output level is 300 mV (full "Leslie Volume"). The separate AMP output (plug ring) may be used with transistor leslies to obtain the nice tube overdrive effect provided by HX3. On higher "Leslie Volume" levels, you will notice the tube overdrive/distortion of simulated 6550 output stage.
• SWELL: Expression pedal input is compatible with Yamaha FC-7 and similar expression pedals (direct connection preferred for speed/accuracy, but may also be remoted by MIDI CC 11).
• FOOTSW: Single or double Footswich controls simulated Leslie speed: SLOW/FAST on plug tip, RUN/STOP on plug ring. Please use latching foot switches; momentary (button type) switches are not supported. Detailed informantion on HX3 usage can be found on Bedienungshinweise page (sorry, german language - use Google translation service). If single footswitch used, Leslie is always on RUN (no plug ring, input grouded by plug sleeve).
• DC IN: Use stabilized DC wall wart 9 to 12V with at least 800mA current output, inner/outer plug diameter 2.1/5.5 mm on DC input jack. Regard jumper setting of JP12 (see above - must be removed for 9 to 12V voltages). Alternatively, use stabilized DC wall wart 5V/1A with jumper JP12 installed.

See HX3 MenuPanel user manual for menu system description.