HX3 mk3/mk4 additional info: Unterschied zwischen den Versionen

Aus KeyboardPartner Wiki
Zur Navigation springenZur Suche springen
KKeine Bearbeitungszusammenfassung
KKeine Bearbeitungszusammenfassung
Zeile 1: Zeile 1:
[[Datei:Mk3 midiout.JPG|400px|thumb|right|'''Jumper wires (supplied with HX3 mk3 board) configuring left MIDI DIN jack as standard MIDI OUT.''']]
[[Datei:Mk3 midiout.JPG|400px|thumb|right|'''Jumper wires (supplied with HX3 mk3 board) configuring left MIDI DIN jack as standard MIDI OUT.''']]


[[Datei:Mk3 midiin.JPG|400px|thumb|right|'''Jumper wires configuring left MIDI DIN jack as secondary MIDI IN (wires may be replaced by jumper bridges). Phantom supply on secondary MIDI IN may be enabled by placing one jumper to two rightmost pins of PL6 and one jumper on JP13. When phantom supply jumpers are installed, DIN jack carries ground on middle pin and +5V on two otherwise unused outer pins.''']]
[[Datei:Mk3 midiin.JPG|400px|thumb|right|'''Jumper wires configuring left MIDI DIN jack as secondary MIDI IN (wires may be replaced by jumper bridges). Jumpers for phantom supply of secondary MIDI input are not installed here.''']]


[[Datei:ftdi.jpg|450px|thumb|right|'''FTDI Cable connected to HX3 board. Your board may be equipped with a non-angled or white pin header; just regard wire colours.''']]
[[Datei:ftdi.jpg|450px|thumb|right|'''FTDI Cable connected to HX3 board. Your board may be equipped with a non-angled or white pin header; just regard wire colours.''']]
Zeile 26: Zeile 26:


Both MIDI DIN jacks are wired by internal jumpers as MIDI inputs with merge as pictured. '''Please disregard lettering on HX3 MIDI expander back panel.''' You may use a MIDI master keyboard and a additional MIDI keyboard or MIDI drawbar controller. Original MIDI OUT configuration may be obtained by internal jumper setting. Also, MIDI phantom supply may be routed to left MIDI input by placing two additional jumpers.
Both MIDI DIN jacks are wired by internal jumpers as MIDI inputs with merge as pictured. '''Please disregard lettering on HX3 MIDI expander back panel.''' You may use a MIDI master keyboard and a additional MIDI keyboard or MIDI drawbar controller. Original MIDI OUT configuration may be obtained by internal jumper setting. Also, MIDI phantom supply may be routed to left MIDI input by placing two additional jumpers.
Phantom supply on secondary MIDI IN may be enabled by placing one jumper to two rightmost pins of PL6 and one jumper on JP13. When phantom supply jumpers are installed, DIN jack carries ground on middle pin and +5V on two otherwise unused outer pins.


Factory default for "MIDI Custom CC" set is '''Nord C2''' organ (works also with '''Ocean Beach DB-1''' drawbar controller); all MIDI controller assignments may be changed by ''HX3 Remote'' application (USB adaptor cable required) to any desired value.
Factory default for "MIDI Custom CC" set is '''Nord C2''' organ (works also with '''Ocean Beach DB-1''' drawbar controller); all MIDI controller assignments may be changed by ''HX3 Remote'' application (USB adaptor cable required) to any desired value.

Version vom 25. Oktober 2014, 06:31 Uhr

Jumper wires (supplied with HX3 mk3 board) configuring left MIDI DIN jack as standard MIDI OUT.
Jumper wires configuring left MIDI DIN jack as secondary MIDI IN (wires may be replaced by jumper bridges). Jumpers for phantom supply of secondary MIDI input are not installed here.
FTDI Cable connected to HX3 board. Your board may be equipped with a non-angled or white pin header; just regard wire colours.

New HX3 mk3 Board is equipped with stereo Leslie® simulation, secondary MIDI input and configurable mono audio output jacks.

On factory default for new HX3 mk3, menu item "Jack Config A" yields bass pedal on left (inner) audio jack, plain organ signal (like G-G on B3 AO28) on right (outer) audio jack. "Jack Config B" yields stereo Leslie® simulation on both jacks with added dry bass pedal signal. Both configurations may be changed to any combination with "AudioJ Conf A" and "AudioJ Conf B" menus (scroll down to access).

Jumpers JP5 und JP7/8 (I2C_REV) must be removed during operation - only needed for factory programming. JP6 must be set to REF position (not on HX3 Expander).

HX3 mk3 has an auxiliary connector PL8 behind the audio jacks which carries auido signal as present on jacks. Similar, two connectors PL18 and PL19 are swell (SWL) and footswitch inputs (connected to control jacks) for internal use.

PL16 (not installed) might be used for future use.

HX3 mk3 does not provide separate switch inputs like mk2 did. Instead, button inputs PL7 and PL11 may be re-configured to switch/tab use by setting mask bits in HX3 Remote software (organ defaults page).

HX3 mk3 Tab/Switch Connection

HX3 mk3 does not have additional tab switch inputs PL8/PL12 with same functions as button/LED inputs PL7/PL11. Instead, button/LED toggle pins on PL7/PL11 may be configured individually as switch inputs by HX3 Remote software, Organ Defaults parameters 478 and 479. A checked box indicates a switch input, an unchecked box means a toogling button/LED input. Default is toggle inputs for Panel16 or button connection.

For other connectors, see page HX3_Board_Installation.

HX3 mk3 Secondary MIDI Input

Both MIDI DIN jacks are wired by internal jumpers as MIDI inputs with merge as pictured. Please disregard lettering on HX3 MIDI expander back panel. You may use a MIDI master keyboard and a additional MIDI keyboard or MIDI drawbar controller. Original MIDI OUT configuration may be obtained by internal jumper setting. Also, MIDI phantom supply may be routed to left MIDI input by placing two additional jumpers.

Phantom supply on secondary MIDI IN may be enabled by placing one jumper to two rightmost pins of PL6 and one jumper on JP13. When phantom supply jumpers are installed, DIN jack carries ground on middle pin and +5V on two otherwise unused outer pins.

Factory default for "MIDI Custom CC" set is Nord C2 organ (works also with Ocean Beach DB-1 drawbar controller); all MIDI controller assignments may be changed by HX3 Remote application (USB adaptor cable required) to any desired value.

HX3 mk3 Update

On HX3 mk3, no additional jumpers must be installed for updating with HX3 Remote application.

HX3 MIDI Expander: To access internal configuration port with FTDI USB adaptor cable, please unscrew front panel and remove top lid. MenuPanel should be left connected to view messages on display.