HX3 MIDI expander module: Unterschied zwischen den Versionen

Aus KeyboardPartner Wiki
Zur Navigation springenZur Suche springen
 
(32 dazwischenliegende Versionen desselben Benutzers werden nicht angezeigt)
Zeile 1: Zeile 1:
[[Datei:expander_vorn.jpg|600 px|thumb|right|'''HX3 Expander''' (special edition "plexi signature" for first 3 customers, other versions will have aluminum or black plastic front)]]
[[Datei:expander_vorn.jpg|300 px|thumb|right|'''HX3 Expander''' (special edition "plexi signature" for first 3 customers, other versions will have plain aluminum lid)]]


PAGE UNDER CONSTRUCTION!
HX3 MIDI expander is a tonewheel organ with all B3 features in a small box! Controlled completely via MIDI, selectable CC-sets for NI B4, Hammond XK, Hamichord and other. 30 presets (to be stored locally), many "secret" HX3 parameters tweakable by menu with incremental encoder - like key contact flex and damping for key click response, or AO28 gain adjustments for more or less percussion punch etc. And, of course, it yields the legendary unmatched HX3 sound.


HX3 MIDI expander is a tonewheel organ in a small box! Controlled completely via MIDI, selectable CC-sets for NI B4, Hammond XK, Hamichord and other. 30 presets (to be stored locally), many "secret" HX3 parameters tweakable by menu with incremental encoder - like key contact flex and damping for key click response, or AO28 gain adjustments for more or less percussion punch etc. And, of course, it yields the legendary unmatched HX3 sound.  
OEMs/Resellers will receive an HX3 Expander in kit form on request -- see assembly instructions below.


==Features==
==Features==
* Compact organ emulator module in aluminum box, 222 x 150 x 42 mm
* Compact organ emulator module in aluminum box, 222 x 150 x 42 mm
* Authentic reproduction of generator, tapering, key contacts, percussion and vibrato by FPGA (Field Programmable Gate Array)
* Authentic reproduction of generator, tapering, key contacts, percussion and vibrato by FPGA (Field Programmable Gate Array)
* Extremely low latency of 50 microseconds Key-to-Audio (not >20 ms as with other MIDI expanders and software emulation)
* Extremely low internal latency of 50 microseconds Key-to-Audio (see note below)
* Natural key click by "rattling" contacts
* Natural key click by "rattling" contacts
* Accurate Leslie simulation with separate outputs
* Accurate Leslie simulation with separate 122 amp output
* MIDI IN accepts 5 different MIDI CC sets
* MIDI IN accepts 5 different MIDI CC sets
* 7 LEDs show vibrato and percussion setting
* 7 LEDs show vibrato and percussion setting
* LCD display and menu system with 2x16 presets, virtual drawbars and parameter tuning
* LCD display and menu system with 2x16 presets, virtual drawbars and parameter tuning
* Swell (expression) pedal and footswitch jacks
* Swell (expression) pedal and footswitch jacks
* Built-in DSP reverb with 3 different reverb algorithms
* DC input 9 to 12V, 500 mA min.
'''[https://github.com/keyboardpartner/HX3/blob/master/DOCS_PDF/HX3%20MIDI%20expander%20module.pdf?raw=true User Manual download (PDF)]'''
'''[[HX3 Remote Application]]''' for firmware updates and parameter tweaking


== Kit Assembly ==
== Kit Assembly ==
You will need only a phillips screwdriver to build! The HX3 expander kit comes with fully functional boards, front and rear bezel/panel, cables, screws and aluminum enclosure. Make shure you have a size 1 PH screwdriver handy, also small pliers or metric 5.5 mm wrench to holt the nuts while fastening.


* Install HX3 main board to rear panel. The 4 jack nuts hold the entire board. The 4 washers are to be installed outside of rear bezel.  
'''For OEMs and resellers the HX3 MIDI Expander is available as a pre-assembled kit.'''
* Use M3 screw, locking washer and M3 nut to fasten the voltage regulator to back panel. The voltage regulator's body should have full contact to back panel as it is used as a heat sink.
 
[[Datei:Expander innen.JPG|500px|thumb|right|'''HX3 Expander with mk4 board, inside view. Note ground lug connection and USB interface cabling.''']]
 
You will need a Philips #1 screwdriver, a 2mm Allen wrench, a 2.5mm Allen wrench and a 5.5mm wrench nut to build. The HX3 expander kit comes with fully functional boards, front and rear bezel/panel, cables, screws and aluminum enclosure.
 
* Install HX3 mainboard to rear panel. The 4 jack nuts hold the entire board. Place rubber toe on back of PCB near PL26 (white 6-pin header).
* Use M3 screw, locking washer and M3 nut to fasten the ground lug to back panel. Locking washer is placed inside on aluminum panel.
* Remove protective film from LCD just prior to final installation.
* Remove protective film from LCD just prior to final installation.
* Fasten MenuDisplay board to front panel using 6 M3 bolts with spacers. Space between board and front panel should be approx. 12 mm. Be shure not to bend LED wires.  
* Fasten MenuDisplay board to front plexi panel using 6 M3 Allen screws with 6 plastic spacers and M3 nuts. Do not overtighten screws to prevent cracks in bezel. Use locking washers on each M3 nut.
* Fasten side panels to front panel using 4 self-tapping screws.
* Fasten side panels to back panel using 4 self-tapping Philips screws.
* Insert bottom panel into slots of side panel.
* Insert bottom panel into slots of side panel.
* Connect 2 flat-ribbon cables to board connectors as pictured.  
* Mount USB interface board with short self-tapping screw so USB connector is straight in slot.
* Set jumper JP6 on HX3 main board to desired operation: In position "MONO", organ main and pedal outputs are mixed to one channel on MAIN/BASS output jack (plug tip), in other position to separate channels (pedals on plug "ring", right channel).
* Connect USB interface to HX3 PL26 with short coloured jumper wires. Do not cross cables, use straight one-on-one connection.
* Be shure to remove jumper JP12 (near DC jack) when using a 9 to 12V DC power supply (default: no jumper). If you plan to use a 5V power supply, move jumper from AGND spare position to JP12. Note: Damage will occur if higher voltage than 5V applied whith JP12 installed!
* Connect MenuPanel with flat-ribbon cable to HX3 board PL4.
* Fasten side panels to back panel using 4 self-tapping screws.
* Insert top lid.
* Fasten side panels to front panel using 4 Allen type M3x12mm screws. Do not overtighten screws to prevent cracks in bezel.
* Affix 4 self-adhesive bases to bottom panel in each corner.
* Affix 4 self-adhesive bases to bottom panel in each corner.


You're done! Time to try out: Plug in appropriate power supply 9 to 12V 800mA min. to DC jack. Display will illuminate and show welcome message, serial number and owner information (your name per default). Turn knob to select a preset. LEDs on right side will show corresponding vibrato/percussion setting.
You're done! Time to try out: Plug in appropriate power supply 9 to 12V 800mA min. to DC jack. Display will illuminate and show welcome message, serial number and owner information (your name per default). Turn knob to select a preset. LEDs on right side will show corresponding vibrato/percussion setting.
==Jack Connections==
[[Datei:expander_hinten.jpg|300px|thumb|right|'''HX3 Expander''' (special edition "plexi signature" for first 3 customers, standard versions will have only HX3 logo on top)]]
The HX3 expander module has two "stereo" type 1/4" '''audio output jacks''', one DC input jack and two accessory jacks on back panel.
* '''MAIN/BASS:''' Separate output for main organ manuals (plug tip) and pedal (plug ring) on jack if 3-pin jumper JP6 set to 2-CHANNEL. Use Y-cable or stereo cable to obtain all channels. Outut is mono (mix of manuals and bass) if JP6 set to MONO (only plug tip connected). Output level is approx. 150 mV at full swell.
* '''LESL/AMP:''' Leslie simulation (mono, plug tip) and leslie amp simulation (122 amp without speakers, but with overdrive capabilities, plug ring). Output level is 300 mV (full "Leslie Volume"). The separate AMP output (plug ring) may be used with transistor leslies to obtain the nice tube overdrive effect provided by HX3. On higher "Leslie Volume" levels, you will notice the tube overdrive/distortion of simulated 6550 output stage.
* '''SWELL:''' Expression pedal input is compatible with Yamaha FC-7 and similar expression pedals (direct connection preferred for speed/accuracy, but may also be remoted by MIDI CC 11).
* '''FOOTSW:''' Single or double Footswich controls simulated '''Leslie speed''': SLOW/FAST on plug tip, RUN/STOP on plug ring. Please use latching foot switches; momentary (button type) switches are not supported. Detailed informantion on HX3 usage can be found on '''[[Bedienungshinweise]]''' page (sorry, german language - use Google translation service). If single footswitch used, Leslie is always on RUN (no plug ring, input grouded by plug sleeve).
* '''DC IN:''' Use stabilized DC wall wart 9 to 12V with at least 800mA current output, inner/outer plug diameter 2.1/5.5 mm on DC input jack. Regard jumper setting of JP12 (see above - must be removed for 9 to 12V voltages). Alternatively, use stabilized DC wall wart 5V/1A with jumper JP12 installed.
==Volume Control==
We recommend connecting an expression pedal '''Yamaha FC-7''' or similar (1/4" jack, 10k to 47k resistance) directly to the module, as it has a higher resolution and acts faster than MIDI control by MIDI CC #11. Despite the swell/expression pedal (or MIDI CC #11) there is a "simulated" total volume control by MIDI CC #7. But: It only reduces "travel" of swell pedal, it is not intended as a volume pot substitute (would reduce resolution and S/N ratio due to internal 16 bit audio handling). Anyway, instead of the ORGAN MAIN output you may use the simulated Leslie Amp 122 output instead which has a separate volume pot (for example by MIDI CC $4C hex, 76 decimal in NI B4 MIDI CC set). It may be also be changed by MenuPanel entry "LeslieVolume" (to be reached directly by pressing DATA ENTRY knob after power-on).
==Menu System==
See '''[[HX3 MenuPanel]]''' user manual for menu system description. Note: Some entries do not apply to expander use (i.e. analog enables for drawbars/pots etc.).

Aktuelle Version vom 27. Juli 2015, 11:00 Uhr

HX3 Expander (special edition "plexi signature" for first 3 customers, other versions will have plain aluminum lid)

HX3 MIDI expander is a tonewheel organ with all B3 features in a small box! Controlled completely via MIDI, selectable CC-sets for NI B4, Hammond XK, Hamichord and other. 30 presets (to be stored locally), many "secret" HX3 parameters tweakable by menu with incremental encoder - like key contact flex and damping for key click response, or AO28 gain adjustments for more or less percussion punch etc. And, of course, it yields the legendary unmatched HX3 sound.

OEMs/Resellers will receive an HX3 Expander in kit form on request -- see assembly instructions below.

Features

  • Compact organ emulator module in aluminum box, 222 x 150 x 42 mm
  • Authentic reproduction of generator, tapering, key contacts, percussion and vibrato by FPGA (Field Programmable Gate Array)
  • Extremely low internal latency of 50 microseconds Key-to-Audio (see note below)
  • Natural key click by "rattling" contacts
  • Accurate Leslie simulation with separate 122 amp output
  • MIDI IN accepts 5 different MIDI CC sets
  • 7 LEDs show vibrato and percussion setting
  • LCD display and menu system with 2x16 presets, virtual drawbars and parameter tuning
  • Swell (expression) pedal and footswitch jacks
  • Built-in DSP reverb with 3 different reverb algorithms
  • DC input 9 to 12V, 500 mA min.

User Manual download (PDF)

HX3 Remote Application for firmware updates and parameter tweaking

Kit Assembly

For OEMs and resellers the HX3 MIDI Expander is available as a pre-assembled kit.

HX3 Expander with mk4 board, inside view. Note ground lug connection and USB interface cabling.

You will need a Philips #1 screwdriver, a 2mm Allen wrench, a 2.5mm Allen wrench and a 5.5mm wrench nut to build. The HX3 expander kit comes with fully functional boards, front and rear bezel/panel, cables, screws and aluminum enclosure.

  • Install HX3 mainboard to rear panel. The 4 jack nuts hold the entire board. Place rubber toe on back of PCB near PL26 (white 6-pin header).
  • Use M3 screw, locking washer and M3 nut to fasten the ground lug to back panel. Locking washer is placed inside on aluminum panel.
  • Remove protective film from LCD just prior to final installation.
  • Fasten MenuDisplay board to front plexi panel using 6 M3 Allen screws with 6 plastic spacers and M3 nuts. Do not overtighten screws to prevent cracks in bezel. Use locking washers on each M3 nut.
  • Fasten side panels to back panel using 4 self-tapping Philips screws.
  • Insert bottom panel into slots of side panel.
  • Mount USB interface board with short self-tapping screw so USB connector is straight in slot.
  • Connect USB interface to HX3 PL26 with short coloured jumper wires. Do not cross cables, use straight one-on-one connection.
  • Connect MenuPanel with flat-ribbon cable to HX3 board PL4.
  • Insert top lid.
  • Fasten side panels to front panel using 4 Allen type M3x12mm screws. Do not overtighten screws to prevent cracks in bezel.
  • Affix 4 self-adhesive bases to bottom panel in each corner.

You're done! Time to try out: Plug in appropriate power supply 9 to 12V 800mA min. to DC jack. Display will illuminate and show welcome message, serial number and owner information (your name per default). Turn knob to select a preset. LEDs on right side will show corresponding vibrato/percussion setting.