HX3 KeyB Duo Installation: Unterschied zwischen den Versionen

Aus KeyboardPartner Wiki
Zur Navigation springenZur Suche springen
K (Schützte „HX3 KeyB Duo Installation“ ([Bearbeiten=Nur Administratoren erlauben] (unbeschränkt) [Verschieben=Nur Administratoren erlauben] (unbeschränkt)))
KKeine Bearbeitungszusammenfassung
Zeile 1: Zeile 1:
This page shows installation of an HX3 mainboard (FPGA based) as a replacement for KeyB Duo sound generator (DSP based). Board is completely remoted by MIDI from KeyB controller. All knob/button/drawbar functions are retained.
This page shows installation of an HX3 mainboard (FPGA based) as a replacement for KeyB Duo sound generator (DSP based). Board is completely remoted by MIDI from KeyB controller. All knob/button/drawbar functions are retained. Installation is quite simple, but requires soldering skills and crimping flat ribbon cables. Click pictures to enlarge.


Installation is quite simple, but requires soldering skills and crimping flat ribbon cables. Click pictures to enlarge.
[[Datei:Keyb_1_resize.JPG|480px|thumb|left|'''Remove KeyB DSP board and install HX3 board with plastic spacers, using M3 screws. Some holes must be drilled in base plate. Route 10-wire ribbon cable from PL17 PREAMP CTRL to KeyB controller board.''']]


Replacing the KeyB key scan is optional. Installing a FatarScan2 board for direct connection to HX3 yields much lower key latency.
[[Datei:Keyb_2_resize.JPG|480px|thumb|left|'''Remove old connectors from cables and install new connectors as shown. Audio cables both connect to HX3 stereo output. Ribbon cable to PL14 is required when using FatarScan2 board for key scanning instead of MIDI input. Note position of 220R resistor.''']]


[[Datei:Keyb_3_resize.JPG|480px|thumb|left|'''To prevent KeyB to send MIDI data before HX3 is ready to accept, the KeyB Duo controller RESET must be delayed. This is done by using a signal on wire 8 of HX3 PL17. Solder single wire #8 from ribbon cable to R10 on KeyB controller board as shown. Use R10 pin pointing to U1. Cut off all other wires of PL17 cable.''']]


[[Datei:Keyb_1_resize.JPG|480px|thumb|left|'''Remove KeyB DSP board and install HX3 board with plastic spacers, using M3 screws. Some holes must be drilled in base plate. Route 10-wire ribbon cable from PL17 PREAMP CTRL to KeyB controller board.''']]
Replacing the KeyB key scan is optional. Installing a FatarScan2 board for direct connection to HX3 yields much lower key latency.


[[Datei:Keyb_2_resize.JPG|480px|thumb|left|'''Remove old connectors from cables and install new connectors as shown. Audio cables both connect to HX3 stereo output. Ribbon cable to PL14 is required when using FatarScan2 board for key scanning instead of MIDI input. Note position of 220R resistor.''']]
[[Datei:Keyb_s1_resize.JPG|480px|thumb|left|'''Remove lower KeyB keybed and install FatarScan2 board with plastic spacers, using M3 screws. Some holes must be drilled in base plate. Route 10-wire ribbon cable from HX3 PL14 to FatarScan board. Disconnect Fatar keybed cables from KeyB MIDI controller and install 16-pin flat ribbon connectors, pin 1 pointing to coloured wire.''']]


[[Datei:Keyb_3_resize.JPG|480px|thumb|left|'''To prevent KeyB to send MIDI data before HX3 is ready to accept, the KeyB Duo controller RESET must be delayed. This is done by using a signal on wire 8 of HX3 PL17. Solder wire 8 from ribbon cable to R10 on KeyB controller board as shown. Cut off all other wires.''']]
[[Datei:Keyb_s2_resize.JPG|480px|thumb|left|'''Connect 16-pin connectors to FatarScan2 board. Note position of upper/lower notes matrix section of Fatar keybeds.''']]

Version vom 30. August 2016, 07:16 Uhr

This page shows installation of an HX3 mainboard (FPGA based) as a replacement for KeyB Duo sound generator (DSP based). Board is completely remoted by MIDI from KeyB controller. All knob/button/drawbar functions are retained. Installation is quite simple, but requires soldering skills and crimping flat ribbon cables. Click pictures to enlarge.

Remove KeyB DSP board and install HX3 board with plastic spacers, using M3 screws. Some holes must be drilled in base plate. Route 10-wire ribbon cable from PL17 PREAMP CTRL to KeyB controller board.
Remove old connectors from cables and install new connectors as shown. Audio cables both connect to HX3 stereo output. Ribbon cable to PL14 is required when using FatarScan2 board for key scanning instead of MIDI input. Note position of 220R resistor.
To prevent KeyB to send MIDI data before HX3 is ready to accept, the KeyB Duo controller RESET must be delayed. This is done by using a signal on wire 8 of HX3 PL17. Solder single wire #8 from ribbon cable to R10 on KeyB controller board as shown. Use R10 pin pointing to U1. Cut off all other wires of PL17 cable.

Replacing the KeyB key scan is optional. Installing a FatarScan2 board for direct connection to HX3 yields much lower key latency.

Remove lower KeyB keybed and install FatarScan2 board with plastic spacers, using M3 screws. Some holes must be drilled in base plate. Route 10-wire ribbon cable from HX3 PL14 to FatarScan board. Disconnect Fatar keybed cables from KeyB MIDI controller and install 16-pin flat ribbon connectors, pin 1 pointing to coloured wire.
Connect 16-pin connectors to FatarScan2 board. Note position of upper/lower notes matrix section of Fatar keybeds.