HX3 mk3/mk4 additional info - Versionsgeschichte

Christian: /* HX3 mk4 Changes */

2023-10-13T10:22:33Z

HX3 mk4 Changes

← Nächstältere Version		Version vom 13. Oktober 2023, 10:22 Uhr
Zeile 52:		Zeile 52:
	* Preamp control circuit '''U12''' is alsways populated to use PL17		* Preamp control circuit '''U12''' is alsways populated to use PL17
	* MIDI configuration connector PL6 has been renamed to PL10. You may connect switches to configurate MIDI IN/OUT or use jumpers (see below).		* MIDI configuration connector PL6 has been renamed to PL10. You may connect switches to configurate MIDI IN/OUT or use jumpers (see below).
	* Jumper setting for left MIDI OUT is 1-2, 4-5 and 7-8 on PL10 (3 jumpers, leftmost pin is 1)		* Jumper setting for left MIDI OUT is 1-2, 3-4 and 7-8 on PL10 (3 jumpers, leftmost pin is 1)
	* Jumper setting for left MIDI IN is 2-3 and 6-7 on PL10 (2 jumpers, leftmost pin is 1)		* Jumper setting for left MIDI IN is 2-3 and 6-7 on PL10 (2 jumpers, leftmost pin is 1)
	* For +5V phantom supply on MIDI IN set additional jumper on pins 7-8 and 9-10. When phantom supply jumpers are installed, DIN jack carries ground on middle pin and +5V on two otherwise unused outer pins.		* For +5V phantom supply on MIDI IN set additional jumper on pins 7-8 and 9-10. When phantom supply jumpers are installed, DIN jack carries ground on middle pin and +5V on two otherwise unused outer pins.

Bovist: /* HX3 mk4 Changes */

2016-05-14T10:23:58Z

HX3 mk4 Changes

← Nächstältere Version		Version vom 14. Mai 2016, 10:23 Uhr
Zeile 53:		Zeile 53:
	* MIDI configuration connector PL6 has been renamed to PL10. You may connect switches to configurate MIDI IN/OUT or use jumpers (see below).		* MIDI configuration connector PL6 has been renamed to PL10. You may connect switches to configurate MIDI IN/OUT or use jumpers (see below).
	* Jumper setting for left MIDI OUT is 1-2, 4-5 and 7-8 on PL10 (3 jumpers, leftmost pin is 1)		* Jumper setting for left MIDI OUT is 1-2, 4-5 and 7-8 on PL10 (3 jumpers, leftmost pin is 1)
	* For +5V phantom supply on MIDI IN set additional jumper on pins 9-10. When phantom supply jumpers are installed, DIN jack carries ground on middle pin and +5V on two otherwise unused outer pins.		* Jumper setting for left MIDI IN is 2-3 and 6-7 on PL10 (2 jumpers, leftmost pin is 1)
			* For +5V phantom supply on MIDI IN set additional jumper on pins 7-8 and 9-10. When phantom supply jumpers are installed, DIN jack carries ground on middle pin and +5V on two otherwise unused outer pins.
	* Jumper setting for left MIDI IN is 2-3 and 5-6 on PL10 (2 jumpers, similar second pic)		* Jumper setting for left MIDI IN is 2-3 and 5-6 on PL10 (2 jumpers, similar second pic)
	* PL14 has internal pullups so using FatarScan core with no scan board attached will produce noise.		* PL14 has internal pullups so using FatarScan core with no scan board attached will produce noise.

Bovist: /* HX3 mk4 MIDI Hardware Configuration */

2016-05-12T17:57:11Z

HX3 mk4 MIDI Hardware Configuration

← Nächstältere Version		Version vom 12. Mai 2016, 17:57 Uhr
Zeile 61:		Zeile 61:
	From factory, both MIDI DIN jacks are wired by internal jumpers as MIDI inputs with merge by two jumpers on PL10, bridging pins 2-3 and 5-6. The '''left''' MIDI jack may be configured as a '''MIDI output''' by placing jumpers on PL10 pin '''1-2 and 3-4''' instead of 2-3 and 5-6. Place an additional jumper on '''pins 7-8''' for ground on MIDI output. Seen from back, PL10 pin 1 ist the '''leftmost''' pin.		From factory, both MIDI DIN jacks are wired by internal jumpers as MIDI inputs with merge by two jumpers on PL10, bridging pins 2-3 and 5-6. The '''left''' MIDI jack may be configured as a '''MIDI output''' by placing jumpers on PL10 pin '''1-2 and 3-4''' instead of 2-3 and 5-6. Place an additional jumper on '''pins 7-8''' for ground on MIDI output. Seen from back, PL10 pin 1 ist the '''leftmost''' pin.

	A +5V MIDI phantom supply on outer pins of ~~left~~ MIDI input ~~jack~~ may be obtained by '''additional''' ~~jumper~~ on PL10 '''pins 9-10'''~~. Our BASS25-MIDI board may be supplied via MIDI cable in this way~~. Do not install ~~this jumper~~ if connecting ~~oher~~ MIDI gear not using a phantom supply.		A +5V MIDI phantom supply on outer pins of MIDI input for MIDISCAN25 bass pedal board may be obtained by two '''additional''' jumpers on HX3 PL10 '''pins 7-8 and 9-10'''. Do not install these jumpers if connecting other MIDI gear not using a phantom supply.

	If the Extension board is installed, both MIDI jacks on mainboard should be jumpered as MIDI INs as the Extension board has its own MIDI OUT.		If the Extension board is installed, both MIDI jacks on mainboard should be jumpered as MIDI INs as the Extension board has its own MIDI OUT.

Bovist: /* HX3 mk4 MIDI Hardware Configuration */

2016-05-12T17:55:01Z

HX3 mk4 MIDI Hardware Configuration

← Nächstältere Version		Version vom 12. Mai 2016, 17:55 Uhr
Zeile 61:		Zeile 61:
	From factory, both MIDI DIN jacks are wired by internal jumpers as MIDI inputs with merge by two jumpers on PL10, bridging pins 2-3 and 5-6. The '''left''' MIDI jack may be configured as a '''MIDI output''' by placing jumpers on PL10 pin '''1-2 and 3-4''' instead of 2-3 and 5-6. Place an additional jumper on '''pins 7-8''' for ground on MIDI output. Seen from back, PL10 pin 1 ist the '''leftmost''' pin.		From factory, both MIDI DIN jacks are wired by internal jumpers as MIDI inputs with merge by two jumpers on PL10, bridging pins 2-3 and 5-6. The '''left''' MIDI jack may be configured as a '''MIDI output''' by placing jumpers on PL10 pin '''1-2 and 3-4''' instead of 2-3 and 5-6. Place an additional jumper on '''pins 7-8''' for ground on MIDI output. Seen from back, PL10 pin 1 ist the '''leftmost''' pin.

	A +5V MIDI phantom supply on outer pins of MIDI ~~output~~ jack may be obtained by '''additional''' jumper on PL10 '''pins 9-10'''. Our BASS25-MIDI board may be supplied via MIDI cable in this way. Do not install this jumper if connecting oher MIDI gear not using a phantom supply.		A +5V MIDI phantom supply on outer pins of left MIDI input jack may be obtained by '''additional''' jumper on PL10 '''pins 9-10'''. Our BASS25-MIDI board may be supplied via MIDI cable in this way. Do not install this jumper if connecting oher MIDI gear not using a phantom supply.

	If the Extension board is installed, both MIDI jacks on mainboard should be jumpered as MIDI INs as the Extension board has its own MIDI OUT.		If the Extension board is installed, both MIDI jacks on mainboard should be jumpered as MIDI INs as the Extension board has its own MIDI OUT.

Bovist: /* HX3 mk3/mk4 Tab/Switch Connection */

2016-05-12T17:52:19Z

HX3 mk3/mk4 Tab/Switch Connection

← Nächstältere Version		Version vom 12. Mai 2016, 17:52 Uhr
Zeile 19:		Zeile 19:
	HX3 mk3/mk4 does not have additional tab switch inputs PL8/PL12 with same functiononality as button/LED inputs PL7/PL11. Instead, button/LED toggle pins on PL7/PL11 may be configured individually as switch inputs by ''HX3 Remote'' software, '''Organ Defaults''' parameters 478 and 479. A checked box indicates a switch input, an unchecked box means a toogling button/LED input. Default is toggle inputs for Panel16 or button connection.		HX3 mk3/mk4 does not have additional tab switch inputs PL8/PL12 with same functiononality as button/LED inputs PL7/PL11. Instead, button/LED toggle pins on PL7/PL11 may be configured individually as switch inputs by ''HX3 Remote'' software, '''Organ Defaults''' parameters 478 and 479. A checked box indicates a switch input, an unchecked box means a toogling button/LED input. Default is toggle inputs for Panel16 or button connection.

	For other connectors, see page [[~~HX3_Board_Installation~~]].		For other connectors, see page [[HX3 Board Installation]].

	HX3 mk3 boards have a spare footprint '''U12''' for an additional PCA9554AD I2C port circuit which may be used to control external preamplifiers etc. If populated (standard on mk4), '''PL17''' carries following signals (active high) with firmware #3.6 and up:		HX3 mk3 boards have a spare footprint '''U12''' for an additional PCA9554AD I2C port circuit which may be used to control external preamplifiers etc. If populated (standard on mk4), '''PL17''' carries following signals (active high) with firmware #3.6 and up:

Bovist: /* HX3 mk3/mk4 Firmware Update */

2016-05-12T17:51:55Z

HX3 mk3/mk4 Firmware Update

← Nächstältere Version		Version vom 12. Mai 2016, 17:51 Uhr
Zeile 42:		Zeile 42:
	===HX3 mk3/mk4 Firmware Update===		===HX3 mk3/mk4 Firmware Update===

	On HX3 mk3, '''no''' additional jumpers must be installed for updating with ''HX3 Remote'' application. Please use HX3 Remote application contained in firmware update ZIP.		On HX3 mk3, '''no''' additional jumpers must be installed for updating with ''HX3 Remote'' application. Please use HX3 Remote application contained in firmware update ZIP or HX3 Flash packages provided in Github Repo.

	'''HX3 MIDI Expander:''' To access internal configuration port with FTDI USB adaptor cable, please unscrew front panel and remove top lid. MenuPanel should be left connected to view messages on display. Models with USB port use simple Mini-USB cable instead, no FTDI cable needed.		'''HX3 MIDI Expander:''' To access internal configuration port with FTDI USB adaptor cable, please unscrew front panel and remove top lid. MenuPanel should be left connected to view messages on display. Models with USB port use simple Mini-USB cable instead, no FTDI cable needed.

Bovist: /* HX3 mk4 MIDI Hardware Configuration */

2015-09-26T17:51:04Z

HX3 mk4 MIDI Hardware Configuration

← Nächstältere Version		Version vom 26. September 2015, 17:51 Uhr
Zeile 62:		Zeile 62:

	A +5V MIDI phantom supply on outer pins of MIDI output jack may be obtained by '''additional''' jumper on PL10 '''pins 9-10'''. Our BASS25-MIDI board may be supplied via MIDI cable in this way. Do not install this jumper if connecting oher MIDI gear not using a phantom supply.		A +5V MIDI phantom supply on outer pins of MIDI output jack may be obtained by '''additional''' jumper on PL10 '''pins 9-10'''. Our BASS25-MIDI board may be supplied via MIDI cable in this way. Do not install this jumper if connecting oher MIDI gear not using a phantom supply.

			If the Extension board is installed, both MIDI jacks on mainboard should be jumpered as MIDI INs as the Extension board has its own MIDI OUT.

Bovist am 26. September 2015 um 17:39 Uhr

2015-09-26T17:39:54Z

← Nächstältere Version		Version vom 26. September 2015, 17:39 Uhr
Zeile 1:		Zeile 1:
	[[Datei:Mk3 midiout.JPG\|400px\|thumb\|right\|'''HX3 mk3 jumper wires (supplied with HX3 mk3 board) configuring left MIDI DIN jack as standard MIDI OUT.''']]		[[Datei:Mk3 midiout.JPG\|400px\|thumb\|right\|'''HX3 mk3 jumper wires (supplied with HX3 mk3 board) configuring left MIDI DIN jack as standard MIDI OUT. For HX3 mk4 series, use plain jumpers (see text at bottom).''']]

	[[File:Mk3 midiin.JPG\|400px\|thumb\|right\|'''HX3 mk3 jumper wires configuring left MIDI DIN jack as secondary MIDI IN (wires may be replaced by jumper bridges). Jumpers for phantom supply of secondary MIDI input are not installed here.''']]		[[File:Mk3 midiin.JPG\|400px\|thumb\|right\|'''HX3 mk3 jumper wires configuring left MIDI DIN jack as secondary MIDI IN (wires may be replaced by jumper bridges). Jumpers for phantom supply of secondary MIDI input are not installed here.''']]

Bovist: /* HX3 mk4 Changes */

2015-09-26T17:38:43Z

HX3 mk4 Changes

← Nächstältere Version		Version vom 26. September 2015, 17:38 Uhr
Zeile 48:		Zeile 48:
	===HX3 mk4 Changes===		===HX3 mk4 Changes===

	Inconvenience of jumper cables for MIDI in/out configuration was due to '''design quirk''' on HX3 mk3 boards and has been corrected on mk4 series. HX3 mk4 also has a "preamp control" output with rotary, reverb and drawbar A/B switch control signals on PL17 (see avbove).		Inconvenience of jumper cables for MIDI in/out configuration was due to '''design quirk''' on HX3 mk3 boards and has been corrected on mk4 series. HX3 mk4 also has a "preamp control" output with rotary, reverb and drawbar A/B switch control signals on PL17 (see avbove). Summary:

	Summary:

	* Preamp control circuit '''U12''' is alsways populated to use PL17		* Preamp control circuit '''U12''' is alsways populated to use PL17
	* MIDI configuration connector PL6 has been renamed to PL10. You may connect switches to configurate MIDI IN/OUT or use jumpers (see ~~above~~).		* MIDI configuration connector PL6 has been renamed to PL10. You may connect switches to configurate MIDI IN/OUT or use jumpers (see below).
	* Jumper setting for left MIDI OUT is 1-2, 4-5 and 7-8 on PL10 (3 jumpers, leftmost pin is 1)		* Jumper setting for left MIDI OUT is 1-2, 4-5 and 7-8 on PL10 (3 jumpers, leftmost pin is 1)
	* For +5V phantom supply on MIDI IN set additional jumper on pins 9-10. When phantom supply jumpers are installed, DIN jack carries ground on middle pin and +5V on two otherwise unused outer pins.		* For +5V phantom supply on MIDI IN set additional jumper on pins 9-10. When phantom supply jumpers are installed, DIN jack carries ground on middle pin and +5V on two otherwise unused outer pins.

Bovist: /* HX3 mk4 Changes */

2015-09-26T17:37:47Z

HX3 mk4 Changes

← Nächstältere Version		Version vom 26. September 2015, 17:37 Uhr
Zeile 48:		Zeile 48:
	===HX3 mk4 Changes===		===HX3 mk4 Changes===

	Inconvenience of jumper cables was due to '''design quirk''' on HX3 mk3 boards and has been corrected on mk4 series. HX3 mk4 also has a "preamp control" output with rotary, reverb and drawbar A/B switch control signals on PL17 (see avbove).		Inconvenience of jumper cables for MIDI in/out configuration was due to '''design quirk''' on HX3 mk3 boards and has been corrected on mk4 series. HX3 mk4 also has a "preamp control" output with rotary, reverb and drawbar A/B switch control signals on PL17 (see avbove).

	Summary:		Summary: