HX3 Drawbar Controller - Versionsgeschichte

Bovist: /* Phantom Supply */

2015-12-28T11:04:01Z

Phantom Supply

← Nächstältere Version		Version vom 28. Dezember 2015, 11:04 Uhr
Zeile 68:		Zeile 68:
	For use with HX3 MIDI Expander Plexi with '''HX3 mk4''' version board, you may utilize its “phantom” power supply feature (power over MIDI cable). To enable phantom supply on the HX3 MIDI Expander, you need to open the device and set two jumpers (enclosed with Drawbar Controller package).		For use with HX3 MIDI Expander Plexi with '''HX3 mk4''' version board, you may utilize its “phantom” power supply feature (power over MIDI cable). To enable phantom supply on the HX3 MIDI Expander, you need to open the device and set two jumpers (enclosed with Drawbar Controller package).

	'''Do not open the ~~DrawBarController~~; it has the phantom supply jumper already installed!'''		'''Do not open the DrawbarController; it has the phantom supply jumper already installed!'''

	Remove four Philips screws on back of HX3 Expander Plexi and carefully pull out chassis a few inches. Insert two jumpers supplied with Drawbar Controller to jumper header PL10 on positions 7-8 and 9-10 as shown in picture. Re-assemble USB interface and back plate in reverse order and you’re done.		Remove four Philips screws on back of HX3 Expander Plexi and carefully pull out chassis a few inches. Insert two jumpers supplied with Drawbar Controller to jumper header PL10 on positions 7-8 and 9-10 as shown in picture. Re-assemble USB interface and back plate in reverse order and you’re done.

Bovist: /* Phantom Supply */

2015-12-28T11:03:26Z

Phantom Supply

← Nächstältere Version		Version vom 28. Dezember 2015, 11:03 Uhr
Zeile 66:		Zeile 66:
	[[Datei:Hx3_phantom.jpg\|400px\|thumb\|right\|'''To enable phantom supply via MIDI cable, insert two jumpers to PL10 inside HX3 MIDI Expander as shown (picture applies to mk4 boards only)''']]		[[Datei:Hx3_phantom.jpg\|400px\|thumb\|right\|'''To enable phantom supply via MIDI cable, insert two jumpers to PL10 inside HX3 MIDI Expander as shown (picture applies to mk4 boards only)''']]

	For use with HX3 MIDI Expander with '''HX3 mk4''' version board, you may utilize its “phantom” power supply feature (power over MIDI cable). To enable phantom supply on the HX3 MIDI Expander, you need to open the device and set two jumpers (enclosed with Drawbar Controller package).		For use with HX3 MIDI Expander Plexi with '''HX3 mk4''' version board, you may utilize its “phantom” power supply feature (power over MIDI cable). To enable phantom supply on the HX3 MIDI Expander, you need to open the device and set two jumpers (enclosed with Drawbar Controller package).

	'''Do not open the DrawBarController; it has the phantom supply jumper already installed!'''		'''Do not open the DrawBarController; it has the phantom supply jumper already installed!'''

	Remove four Philips screws on back and carefully pull out chassis a few inches. Insert two jumpers supplied with Drawbar Controller to jumper header PL10 on positions 7-8 and 9-10 as shown in picture. Re-assemble USB interface and back plate in reverse order and you’re done.		Remove four Philips screws on back of HX3 Expander Plexi and carefully pull out chassis a few inches. Insert two jumpers supplied with Drawbar Controller to jumper header PL10 on positions 7-8 and 9-10 as shown in picture. Re-assemble USB interface and back plate in reverse order and you’re done.

	Note for previous version boards: On '''HX3 mk3''', only one jumper fits on rightmost pins of white header. Second jumper must be inserted on position JP13. '''HX3 mk2''' boards do not have a phantom power supply feature.		Note for previous version boards: On '''HX3 mk3''', only one jumper fits on rightmost pins of white header. Second jumper must be inserted on position JP13. '''HX3 mk2''' boards do not have a phantom power supply feature.

Bovist: /* Phantom Supply */

2015-12-28T11:02:54Z

Phantom Supply

← Nächstältere Version		Version vom 28. Dezember 2015, 11:02 Uhr
Zeile 67:		Zeile 67:

	For use with HX3 MIDI Expander with '''HX3 mk4''' version board, you may utilize its “phantom” power supply feature (power over MIDI cable). To enable phantom supply on the HX3 MIDI Expander, you need to open the device and set two jumpers (enclosed with Drawbar Controller package).		For use with HX3 MIDI Expander with '''HX3 mk4''' version board, you may utilize its “phantom” power supply feature (power over MIDI cable). To enable phantom supply on the HX3 MIDI Expander, you need to open the device and set two jumpers (enclosed with Drawbar Controller package).

			'''Do not open the DrawBarController; it has the phantom supply jumper already installed!'''

	Remove four Philips screws on back and carefully pull out chassis a few inches. Insert two jumpers supplied with Drawbar Controller to jumper header PL10 on positions 7-8 and 9-10 as shown in picture. Re-assemble USB interface and back plate in reverse order and you’re done.		Remove four Philips screws on back and carefully pull out chassis a few inches. Insert two jumpers supplied with Drawbar Controller to jumper header PL10 on positions 7-8 and 9-10 as shown in picture. Re-assemble USB interface and back plate in reverse order and you’re done.

Bovist: /* Controls */

2015-12-17T14:48:01Z

Controls

← Nächstältere Version		Version vom 17. Dezember 2015, 14:48 Uhr
Zeile 33:		Zeile 33:
	To assign the 9 drawbars to '''upper manual''', both buttons ASSIGN LOWER and ASSIGN PEDAL must be off. To assign drawbars to '''lower manual''', button ASSIGN LOWER must be ON. To assign drawbars to '''bass pedals''', button ASSIGN PEDAL must be ON.		To assign the 9 drawbars to '''upper manual''', both buttons ASSIGN LOWER and ASSIGN PEDAL must be off. To assign drawbars to '''lower manual''', button ASSIGN LOWER must be ON. To assign drawbars to '''bass pedals''', button ASSIGN PEDAL must be ON.

	If ASSIGN PEDAL is enabled, first two drawbars control 16' and 8' of bass pedal. Third drawbar controls bass pedal '''sustain'''. Three ~~leftmost~~ drawbars control SWELL TRIM CAP (general volume of organ AO28 preamp), TONE and ROTARY AMP simulation volume.		If ASSIGN PEDAL is enabled, first two drawbars control 16' and 8' of bass pedal. Third drawbar controls bass pedal '''sustain'''. Three rightmost drawbars control SWELL TRIM CAP (general volume of organ AO28 preamp), TONE and ROTARY AMP simulation volume.

	===Additional Functions===		===Additional Functions===

Bovist: /* Phantom Supply */

2015-12-16T18:08:57Z

Phantom Supply

← Nächstältere Version		Version vom 16. Dezember 2015, 18:08 Uhr
Zeile 64:		Zeile 64:
	=== Phantom Supply ===		=== Phantom Supply ===

	[[Datei:Hx3_phantom.jpg\|400px\|thumb\|right\|'''To enable phantom supply via MIDI cable, insert two jumpers to PL10 inside HX3 MIDI Expander as shown.''']]		[[Datei:Hx3_phantom.jpg\|400px\|thumb\|right\|'''To enable phantom supply via MIDI cable, insert two jumpers to PL10 inside HX3 MIDI Expander as shown (picture applies to mk4 boards only)''']]

	For use with HX3 MIDI Expander with '''HX3 mk4''' version board, you may utilize its “phantom” power supply feature (power over MIDI cable). To enable phantom supply on the HX3 MIDI Expander, you need to open the device and set two jumpers (enclosed with Drawbar Controller package).		For use with HX3 MIDI Expander with '''HX3 mk4''' version board, you may utilize its “phantom” power supply feature (power over MIDI cable). To enable phantom supply on the HX3 MIDI Expander, you need to open the device and set two jumpers (enclosed with Drawbar Controller package).

Bovist: /* Updating the HX3 Drawbar Controller (OEM) */

2015-12-16T18:07:47Z

Updating the HX3 Drawbar Controller (OEM)

← Nächstältere Version		Version vom 16. Dezember 2015, 18:07 Uhr
Zeile 243:		Zeile 243:
	it is the same ISP programmer port used in HX3 Remote.		it is the same ISP programmer port used in HX3 Remote.

	~~USe~~ only programming ~~HEX/EEP~~ files provided by KeyboardPartner. Double-click "CommandPrompt" in "DBC_Programming" folder. Type:		Use only programming files provided by KeyboardPartner. Double-click "CommandPrompt" in "DBC_Programming" folder. Type:

	''dbcupd_p XX''		''dbcupd_p XX''

Bovist: /* Updating the HX3 Drawbar Controller (OEM) */

2015-12-16T18:06:54Z

Updating the HX3 Drawbar Controller (OEM)

← Nächstältere Version		Version vom 16. Dezember 2015, 18:06 Uhr
Zeile 243:		Zeile 243:
	it is the same ISP programmer port used in HX3 Remote.		it is the same ISP programmer port used in HX3 Remote.

	Double-click "CommandPrompt" in "DBC_Programming" folder. Type:		USe only programming HEX/EEP files provided by KeyboardPartner. Double-click "CommandPrompt" in "DBC_Programming" folder. Type:

	''dbcupd_p XX''		''dbcupd_p XX''

Bovist: /* Additional Functions */

2015-12-16T18:05:48Z

Additional Functions

← Nächstältere Version		Version vom 16. Dezember 2015, 18:05 Uhr
Zeile 60:		Zeile 60:
	Hold V1 plus V2 plus V3 button to set MIDI channel 7<br>		Hold V1 plus V2 plus V3 button to set MIDI channel 7<br>

	MIDI channels for lower manual and bass pedals are consecutive, i.e. upper +1 for lower and upper +2 for pedals assignment. On power-up, V1 to V3 LEDs indicate selected MIDI channel by flashing 3 times on startup.		MIDI channels for lower manual and bass pedals are consecutive, i.e. upper +1 for lower and upper +2 for pedals assignment. On power-up, V1 to V3 LEDs indicate selected MIDI channel by flashing 3 times on startup. Factory default is channel 1, so V1 LED will flash.

	=== Phantom Supply ===		=== Phantom Supply ===

Bovist: /* Additional Functions */

2015-12-16T18:04:40Z

Additional Functions

← Nächstältere Version		Version vom 16. Dezember 2015, 18:04 Uhr
Zeile 48:		Zeile 48:

	DBC will filter SysEx, real time data and other stuff to clean up MIDI transmission by default.		DBC will filter SysEx, real time data and other stuff to clean up MIDI transmission by default.
	Filters do only affect MIDI data sent to MIDI MERGE input, not directly to HX3's secondary MIDI input.		Filters do '''only''' affect MIDI data sent to MIDI MERGE input, not directly to HX3's secondary MIDI input.

	MIDI send channel for upper manual is selected in a similar way on power-up:		MIDI send channel for upper manual is selected in a similar way on power-up:
Zeile 60:		Zeile 60:
	Hold V1 plus V2 plus V3 button to set MIDI channel 7<br>		Hold V1 plus V2 plus V3 button to set MIDI channel 7<br>

	MIDI channels for lower manual and bass pedals are consecutive, i.e. +1 for lower and +2 for pedals assignment. On power-up, V1 to V3 LEDs indicate selected MIDI channel by flashing 3 times on startup.		MIDI channels for lower manual and bass pedals are consecutive, i.e. upper +1 for lower and upper +2 for pedals assignment. On power-up, V1 to V3 LEDs indicate selected MIDI channel by flashing 3 times on startup.

	=== Phantom Supply ===		=== Phantom Supply ===

Bovist: /* Usage */

2015-12-16T18:03:17Z

Usage

← Nächstältere Version		Version vom 16. Dezember 2015, 18:03 Uhr
Zeile 19:		Zeile 19:
	==Usage==		==Usage==

	HX3 MIDI Expander (or any other HX3 sound module) and HX3 Drawbar Controller should be ~~switched on~~ the same time; switch on HX3 sound module first if HX3 Drawbar Controller is not phantom-powered. On power-up (either through MIDI phanton supply or wall wart), HX3 Drawbar Controller will wait a few seconds until HX3 module is ready to accept MIDI data. Wait time is indicated by a "running light" on button LEDs. After wait time, HX3 Drawbar Controller will send all its MIDI controller data to the host so both settings are consistent.		HX3 MIDI Expander (or any other HX3 sound module) and HX3 Drawbar Controller should be powered the same time; switch on HX3 sound module first if HX3 Drawbar Controller is not phantom-powered. On power-up (either through MIDI phanton supply or wall wart), HX3 Drawbar Controller will wait a few seconds until HX3 module is ready to accept MIDI data. Wait time is indicated by a "running light" on button LEDs. After wait time, HX3 Drawbar Controller will send all its MIDI controller data to the host so both settings are consistent.

	===Connection===		===Connection===