HX3 Board Installation - Versionsgeschichte

Bovist: /* Preset 12-2 */

2018-11-08T15:53:00Z

Preset 12-2

← Nächstältere Version		Version vom 8. November 2018, 15:53 Uhr
Zeile 217:		Zeile 217:
	13,14: Common switch ground (0V)		13,14: Common switch ground (0V)

	Note: The old Preset12-MPX boards for HX3 mk2/mk3 may be used as well for HX3 mk4 and mk5. They do not offer a variable preset number for second drawbar set, though. Instead, second drawbar set is hard-wired to Voice Preset 15. So you have to change 2nd drawbar set number in parameter #1496 (HX3.5) resp #496 (HX3.4) to 15, not to 1.		Note: The old '''Preset12-MPX''' boards for HX3 mk2/mk3 may be used as well for HX3 mk4 and mk5. They do not offer a variable preset number for second drawbar set, though. Instead, second drawbar set is hard-wired to Voice Preset 15. So you have to change 2nd drawbar set number in parameter #1496 (HX3.5) resp #496 (HX3.4) to 15, not to 1.

	==Connecting Keyboard Scan Board(s)==		==Connecting Keyboard Scan Board(s)==

Bovist: /* Preset 12-2 */

2018-11-08T15:52:40Z

Preset 12-2

← Nächstältere Version		Version vom 8. November 2018, 15:52 Uhr
Zeile 216:		Zeile 216:
	12: Switch 12 (Preset 11, CANCEL key)<br>		12: Switch 12 (Preset 11, CANCEL key)<br>
	13,14: Common switch ground (0V)		13,14: Common switch ground (0V)

			Note: The old Preset12-MPX boards for HX3 mk2/mk3 may be used as well for HX3 mk4 and mk5. They do not offer a variable preset number for second drawbar set, though. Instead, second drawbar set is hard-wired to Voice Preset 15. So you have to change 2nd drawbar set number in parameter #1496 (HX3.5) resp #496 (HX3.4) to 15, not to 1.

	==Connecting Keyboard Scan Board(s)==		==Connecting Keyboard Scan Board(s)==

Bovist: /* Connecting Analog Inputs */

2017-03-08T17:40:10Z

Connecting Analog Inputs

← Nächstältere Version		Version vom 8. März 2017, 17:40 Uhr
Zeile 41:		Zeile 41:
	==Connecting Analog Inputs==		==Connecting Analog Inputs==

	HX3 provides 24 analog inputs, all located on pin headers PL9 and PL13. All analog inputs are DC controlled. Input voltage range is from 0V (off or minimal volume) to +3.3V (max. volume). HX3 may also be used '''without any switches/drawbars/pots connected''' by ~~selecting "No Analog Inputs" in HX3 Remote parameter 478 (~~Expander ~~Mode)~~. You may leave all internal connectors open if you plan to remote by MIDI only with analog control inputs disabled. Note: One analog input is internally tied to SWELL jack and should remain open.		HX3 provides 24 analog inputs, all located on pin headers PL9 and PL13. All analog inputs are DC controlled. Input voltage range is from 0V (off or minimal volume) to +3.3V (max. volume). HX3 may also be used '''without any switches/drawbars/pots connected''' by installing the MIDI Expander firmware. You may leave all internal connectors open if you plan to remote by MIDI only with analog control inputs disabled. Note: One analog input is internally tied to SWELL jack and should remain open.

	===Connecting Drawbar 9/11/12 Boards===		===Connecting Drawbar 9/11/12 Boards===

Bovist: /* Bass25 */

2017-03-07T21:39:30Z

Bass25

← Nächstältere Version		Version vom 7. März 2017, 21:39 Uhr
Zeile 258:		Zeile 258:
	26: Common ground (busbar)		26: Common ground (busbar)

	'''JP3 and JP4''' solder bridges must be closed. 2-pin inline header provides common ground for the busbar.		'''JP3 and JP4''' solder bridges must be closed. 2-pin inline header PL9 also provides common ground for the busbar.

	Note: A third Scan16-Strip or Scan61-Inline board may alternatively be used for bass pedal instead of Bass25, using only the first 13 or 25 contact inputs. Set jumper JP3 on scan boards to enable them for bass pedal use.		Note: A third Scan16-Strip or Scan61-Inline board may alternatively be used for bass pedal instead of Bass25, using only the first 13 or 25 contact inputs. Set jumper JP3 on scan boards to enable them for bass pedal use.

Bovist: /* Bass25 MIDI */

2017-03-07T21:38:23Z

Bass25 MIDI

← Nächstältere Version		Version vom 7. März 2017, 21:38 Uhr
Zeile 276:		Zeile 276:
	'''JP4''' solder bridge must be closed if Bass25 MIDI is powered by phantom supply from HX3 board, left MIDI input jack (seen from back). MIDI phantom power jumpers on HX3 board must be inserted (mk3 and mk4 boards only).		'''JP4''' solder bridge must be closed if Bass25 MIDI is powered by phantom supply from HX3 board, left MIDI input jack (seen from back). MIDI phantom power jumpers on HX3 board must be inserted (mk3 and mk4 boards only).

	For separate power supply (internal +5V or external 9V DC wall wart), open '''JP4''' solder bridge. Use 2-pin header PL12 next to MIDI OUT jack to supply internal +5V: Pin 1 (left, facing towards diode) is VCC +5V, pin 2 (right) is ground (refer to ~~PDFs~~ in [https://github.com/heise/HOAX/tree/master/PLATINEN/Bass25 our Github repo folder PLATNEN/BASS25]).		For separate power supply (internal +5V or external 9V DC wall wart), open '''JP4''' solder bridge. Use 2-pin header PL12 next to MIDI OUT jack to supply internal +5V: Pin 1 (left, facing towards diode) is VCC +5V, pin 2 (right) is ground (refer to PDF schematics in [https://github.com/heise/HOAX/tree/master/PLATINEN/Bass25 our Github repo folder PLATNEN/BASS25]).

	A +5V MIDI phantom supply on outer pins of MIDI input may be obtained from HX3 mainboard by inserting two '''additional''' jumpers on HX3 PL10 '''pins 7-8 and 9-10'''. Do not install these jumpers if connecting other MIDI gear not using a phantom supply.		A +5V MIDI phantom supply on outer pins of MIDI input may be obtained from HX3 mainboard by inserting two '''additional''' jumpers on HX3 PL10 '''pins 7-8 and 9-10'''. Do not install these jumpers if connecting other MIDI gear not using a phantom supply.

Bovist: /* Bass25 MIDI */

2017-03-07T21:37:54Z

Bass25 MIDI

← Nächstältere Version		Version vom 7. März 2017, 21:37 Uhr
Zeile 276:		Zeile 276:
	'''JP4''' solder bridge must be closed if Bass25 MIDI is powered by phantom supply from HX3 board, left MIDI input jack (seen from back). MIDI phantom power jumpers on HX3 board must be inserted (mk3 and mk4 boards only).		'''JP4''' solder bridge must be closed if Bass25 MIDI is powered by phantom supply from HX3 board, left MIDI input jack (seen from back). MIDI phantom power jumpers on HX3 board must be inserted (mk3 and mk4 boards only).

	For separate power supply (internal +5V or external 9V DC wall wart), open '''JP4''' solder bridge. Use 2-pin header PL12 next to MIDI OUT jack to supply internal +5V: Pin 1 (left, facing towards diode) is VCC +5V, pin 2 (right) is ground.		For separate power supply (internal +5V or external 9V DC wall wart), open '''JP4''' solder bridge. Use 2-pin header PL12 next to MIDI OUT jack to supply internal +5V: Pin 1 (left, facing towards diode) is VCC +5V, pin 2 (right) is ground (refer to PDFs in [https://github.com/heise/HOAX/tree/master/PLATINEN/Bass25 our Github repo folder PLATNEN/BASS25]).

	A +5V MIDI phantom supply on outer pins of MIDI input may be obtained from HX3 mainboard by inserting two '''additional''' jumpers on HX3 PL10 '''pins 7-8 and 9-10'''. Do not install these jumpers if connecting other MIDI gear not using a phantom supply.		A +5V MIDI phantom supply on outer pins of MIDI input may be obtained from HX3 mainboard by inserting two '''additional''' jumpers on HX3 PL10 '''pins 7-8 and 9-10'''. Do not install these jumpers if connecting other MIDI gear not using a phantom supply.

Bovist: /* Bass25 */

2017-03-07T21:37:29Z

Bass25

← Nächstältere Version		Version vom 7. März 2017, 21:37 Uhr
Zeile 233:		Zeile 233:
	[[Datei:Midibass25.JPG\|300px\|thumb\|right\|'''Bass25 and Bass25 MIDI (top right) with own MIDI OUT and phantom supply''']]		[[Datei:Midibass25.JPG\|300px\|thumb\|right\|'''Bass25 and Bass25 MIDI (top right) with own MIDI OUT and phantom supply''']]

	[http://shop.keyboardpartner.de/epages/13705466.sf/de_DE/?ObjectPath=/Shops/13705466/Products/bass25 Bass25] scan board (refer to PDFs in [https://github.com/heise/HOAX/tree/master/PLATINEN/Bass25 our Github repo folder PLATNEN/BASS25]~~, files *_new.PDF~~) may be used as an addition to FatarScan2, OrganScan61, Scan61-Inline and Scan16-Strip boards for convenient connection of bass pedal contacts as pictured above (note different HX3 headers). Board may be placed in bottom of organ if 10-wire flat ribbon cable to HX3 or last OrganScan61 board does not exceed 1m. Please note jumper setting on Bass25:		[http://shop.keyboardpartner.de/epages/13705466.sf/de_DE/?ObjectPath=/Shops/13705466/Products/bass25 Bass25] scan board (refer to PDFs in [https://github.com/heise/HOAX/tree/master/PLATINEN/Bass25 our Github repo folder PLATNEN/BASS25]) may be used as an addition to FatarScan2, OrganScan61, Scan61-Inline and Scan16-Strip boards for convenient connection of bass pedal contacts as pictured above (note different HX3 headers). Board may be placed in bottom of organ if 10-wire flat ribbon cable to HX3 or last OrganScan61 board does not exceed 1m. Please note jumper setting on Bass25:

	'''Old version''' (beige PCB):		'''Old version''' (beige PCB):

Bovist: /* Bass25 MIDI */

2017-03-07T21:36:47Z

Bass25 MIDI

← Nächstältere Version		Version vom 7. März 2017, 21:36 Uhr
Zeile 264:		Zeile 264:
	===Bass25 MIDI===		===Bass25 MIDI===

	[http://shop.keyboardpartner.de/epages/13705466.sf/de_DE/?ObjectPath=/Shops/13705466/Products/bass25midi Bass25 MIDI] is equipped with an own MIDI controller and MIDI output jack. It is connected to HX3 mk3/mk4 main board by 5-wire MIDI cable. Bass25 MIDI provides in-line headers and a 26-pin flat ribbon cable connector for alternative connection of bass pedal contacts:		[http://shop.keyboardpartner.de/epages/13705466.sf/de_DE/?ObjectPath=/Shops/13705466/Products/bass25midi Bass25 MIDI] is equipped with an own MIDI controller and MIDI output jack. It is connected to HX3 mk3/mk4 main board by 5-wire MIDI cable. Bass25 MIDI provides in-line headers and a 26-pin flat ribbon cable connector for alternative connection of bass pedal contacts. 2-pin inline header PL9 also provides common ground for the busbar.

	Pin - function (active low – switch to Gnd)<br>		Pin - function (active low – switch to Gnd)<br>
Zeile 272:		Zeile 272:
	26: Common ground (busbar)		26: Common ground (busbar)

	'''JP3 ~~and JP4~~''' solder ~~bridges~~ must be closed~~. 2-pin inline header provides common ground for the busbar~~.		'''JP3''' solder bridge must be closed.

	'''~~JP3 and~~ JP4''' solder ~~bridges~~ must be closed. Bass25 MIDI is powered by phantom supply from HX3 board, left MIDI input jack (seen from back). MIDI phantom power jumpers on HX3 board must be inserted (mk3 and mk4 boards only)~~. For separate supply, use 2-pin header next to MIDI OUT jack and open '''JP4''' solder bridge~~.		'''JP4''' solder bridge must be closed if Bass25 MIDI is powered by phantom supply from HX3 board, left MIDI input jack (seen from back). MIDI phantom power jumpers on HX3 board must be inserted (mk3 and mk4 boards only).

	A +5V MIDI phantom supply on outer pins of MIDI input may be obtained by two '''additional''' jumpers on HX3 PL10 '''pins 7-8 and 9-10'''. Do not install these jumpers if connecting other MIDI gear not using a phantom supply.		For separate power supply (internal +5V or external 9V DC wall wart), open '''JP4''' solder bridge. Use 2-pin header PL12 next to MIDI OUT jack to supply internal +5V: Pin 1 (left, facing towards diode) is VCC +5V, pin 2 (right) is ground.

			A +5V MIDI phantom supply on outer pins of MIDI input may be obtained from HX3 mainboard by inserting two '''additional''' jumpers on HX3 PL10 '''pins 7-8 and 9-10'''. Do not install these jumpers if connecting other MIDI gear not using a phantom supply.

	===Scan16-Strip Set===		===Scan16-Strip Set===

Bovist: /* Connecting Drawbar 9/11/12 Boards */

2016-06-29T13:31:16Z

Connecting Drawbar 9/11/12 Boards

← Nächstältere Version		Version vom 29. Juni 2016, 13:31 Uhr
Zeile 52:		Zeile 52:
	Drawbar9 and Drawbar11/12 are compatible and interchangeable, despite additional drawbars for bass pedals resp. tone/amp volume.		Drawbar9 and Drawbar11/12 are compatible and interchangeable, despite additional drawbars for bass pedals resp. tone/amp volume.

	Note to '''HX3 mk2/mk3''' users: Older HX3 boards do not provide a drawbar set switching signal for Drawbar 9-MPX on Pin 15 of PL9 and PL13. From firmware #3.925 and up, switching signals are provided on PL5 pin 6 (upper) and pin 7 (lower). You have to route two single wires from these pins to each PL43 of Drawbar9-MPX (middle pin).		Note to '''HX3 mk2/mk3''' users: Older HX3 boards do not provide a drawbar set switching signal for Drawbar 9-MPX on Pin 15 of PL9 and PL13. From firmware #3.925 and up, switching signals are provided on vibrato knob port PL5 (otherwise unused) pin 6 (upper manual drawbars) and pin 7 (lower). You have to route two single wires from these pins to each PL43 of Drawbar9-MPX (middle pin).

	===Connecting other Drawbar Pots===		===Connecting other Drawbar Pots===

Bovist: /* Connecting Drawbar 9/11/12 Boards */

2016-06-29T13:28:17Z

Connecting Drawbar 9/11/12 Boards

← Nächstältere Version		Version vom 29. Juni 2016, 13:28 Uhr
Zeile 45:		Zeile 45:
	===Connecting Drawbar 9/11/12 Boards===		===Connecting Drawbar 9/11/12 Boards===

	[[Datei:Db9mpx2.JPG\|300px\|thumb\|right\|'''Lower manual configuration with ~~Drawbar 12~~ (A# preset key, left) and ~~Drawbar 9~~-MPX (B preset key, right). Connects to HX3 via long flat ribbon cable (right). Upper manual configuration is similar, but uses Drawbar9 or Drawbar11 instead of Drawbar12.''']]		[[Datei:Db9mpx2.JPG\|300px\|thumb\|right\|'''Lower manual configuration with Drawbar12 (A# preset key, left) and Drawbar9-MPX (B preset key, right). Connects to HX3 via long flat ribbon cable (right). Upper manual configuration is similar, but uses Drawbar9 or Drawbar11 instead of Drawbar12.''']]
	[[Datei:Wiring_drawbars.png\|300px\|thumb\|right\|'''Drawbar and pot connection to PL9 and PL13 (click picture to enlarge)''']]		[[Datei:Wiring_drawbars.png\|300px\|thumb\|right\|'''Drawbar and pot connection to PL9 and PL13 (click picture to enlarge)''']]

	Connection to our [http://shop.keyboardpartner.de/epages/13705466.sf/de_DE/?ObjectPath=/Shops/13705466/Categories/Category1/Register_und_PresetPlatinen drawbar boards ~~Drawbar 9~~ and ~~Drawbar 12~~] is very simple: ~~Drawbar 9~~ (upper) connects to '''PL9''', ~~Drawbar 12~~ (lower) connects to '''PL13''' via 16-wire flat ribbon cable (length up to 1m, plugs wired 1:1). ~~Drawbar 9~~ provides 3-pin headers for connection of Tone and Amp122 Volume pots; may be disabled by ''HX3 Remote'' parameter 481 if adusted by MenuPanel. Additional ~~Drawbar 9~~-MPX boards may be inserted for "two drawbar sets per manual" configurations. Note that ~~Drawbar 9~~-MPX must be the right drawbar set for each manual as on Hammond Consoles (see picture).		Connection to our [http://shop.keyboardpartner.de/epages/13705466.sf/de_DE/?ObjectPath=/Shops/13705466/Categories/Category1/Register_und_PresetPlatinen drawbar boards Drawbar9 and Drawbar12] is very simple: Drawbar9 (upper) connects to '''PL9''', Drawbar12 (lower) connects to '''PL13''' via 16-wire flat ribbon cable (length up to 1m, plugs wired 1:1). Drawbar9 provides 3-pin headers for connection of Tone and Amp122 Volume pots; may be disabled by ''HX3 Remote'' parameter 481 if adusted by MenuPanel. Additional Drawbar9-MPX boards may be inserted for "two drawbar sets per manual" configurations. Note that Drawbar9-MPX must be the right drawbar set for each manual as on Hammond Consoles (see picture).

	~~Drawbar 9~~ and ~~Drawbar 11~~/12 are compatible and interchangeable, despite additional drawbars for bass pedals resp. tone/amp volume.		Drawbar9 and Drawbar11/12 are compatible and interchangeable, despite additional drawbars for bass pedals resp. tone/amp volume.

			Note to '''HX3 mk2/mk3''' users: Older HX3 boards do not provide a drawbar set switching signal for Drawbar 9-MPX on Pin 15 of PL9 and PL13. From firmware #3.925 and up, switching signals are provided on PL5 pin 6 (upper) and pin 7 (lower). You have to route two single wires from these pins to each PL43 of Drawbar9-MPX (middle pin).

	===Connecting other Drawbar Pots===		===Connecting other Drawbar Pots===