HX3.6 Installation Manual - Versionsgeschichte

Bovist: /* Separate Buttons or Switches */

2025-10-26T09:20:00Z

Separate Buttons or Switches

← Nächstältere Version		Version vom 26. Oktober 2025, 09:20 Uhr
Zeile 564:		Zeile 564:
	[[Datei:Hoax_ledbtn.png\|300px\|thumb\|right\|'''Connection of buttons with LEDs on PL35 PERC/VIBON and PL36 PRESET/EFX/SPLIT. Use an R value of 1k for blue or white LEDs, as these LEDs are very bright.''']]		[[Datei:Hoax_ledbtn.png\|300px\|thumb\|right\|'''Connection of buttons with LEDs on PL35 PERC/VIBON and PL36 PRESET/EFX/SPLIT. Use an R value of 1k for blue or white LEDs, as these LEDs are very bright.''']]

	Instead of Panel16 you can also connect your own buttons or tab switches (up to 16) directly to the HX3.6 main board. Each function is activated either by a button or a switch (depending on the ~~parameter~~ '''~~Button Mask~~''' in ~~the system settings of the~~ HX3.6 editor) at the digital inputs PL35/PL36. For buttons, a momentary contact with ground on each PL35/PL36 pin toggles the status and drives indicator LEDs (see schematic). For switches, the indicator LED can be omitted since the mechanical switch indicates the current state. Leave unused digital inputs open.		Instead of Panel16 you can also connect your own buttons or tab switches (up to 16) directly to the HX3.6 main board. Each function is activated either by a button or a switch (depending on the parameters '''Input Mode''' in HX3 editor) at the digital inputs PL35/PL36. For buttons, a momentary contact with ground on each PL35/PL36 pin toggles the status and drives indicator LEDs (see schematic). For switches, the indicator LED can be omitted since the mechanical switch indicates the current state. Leave unused digital inputs open.

	===Panel16===		===Panel16===

Bovist: /* Connecting Drawbar Boards DB9/DB11/DB12 */

2025-10-26T09:15:58Z

Connecting Drawbar Boards DB9/DB11/DB12

← Nächstältere Version		Version vom 26. Oktober 2025, 09:15 Uhr
Zeile 341:		Zeile 341:
	===Connecting Drawbar Boards DB9/DB11/DB12===		===Connecting Drawbar Boards DB9/DB11/DB12===

	[[Datei:Wiring_drawbars.png\|300px\|thumb\|right\|'''Drawbar and pot connection to ~~PL22~~ and ~~PL23~~ (click picture to enlarge)''']]		[[Datei:Wiring_drawbars.png\|300px\|thumb\|right\|'''Drawbar and pot connection to PL31 and PL32 (click picture to enlarge)''']]
	[[Datei:Db9mpx2.JPG\|300px\|thumb\|right\|'''Lower manual configuration with Drawbar12 (A# preset key, left) and Drawbar9-MPX (B preset key, right). Connects to HX3 via long flat ribbon cable (right). Upper manual configuration is similar, but uses Drawbar9 or Drawbar11 instead of Drawbar12.''']]		[[Datei:Db9mpx2.JPG\|300px\|thumb\|right\|'''Lower manual configuration with Drawbar12 (A# preset key, left) and Drawbar9-MPX (B preset key, right). Connects to HX3 via long flat ribbon cable (right). Upper manual configuration is similar, but uses Drawbar9 or Drawbar11 instead of Drawbar12.''']]

Bovist: /* Vibrato Knob (Rotary Switch) */

2025-10-26T08:59:50Z

Vibrato Knob (Rotary Switch)

← Nächstältere Version		Version vom 26. Oktober 2025, 08:59 Uhr
Zeile 616:		Zeile 616:

	[[Datei:Hoax_rotary.png\|300px\|thumb\|right\|'''Vibrato rotary switch connection to PL33 VIBSW. Disregard "PL5" lettering in schematic. First contact lug of rotary switch is not used!''']]		[[Datei:Hoax_rotary.png\|300px\|thumb\|right\|'''Vibrato rotary switch connection to PL33 VIBSW. Disregard "PL5" lettering in schematic. First contact lug of rotary switch is not used!''']]
	[[Datei:Legacy_LED_indicators.png\|300px\|thumb\|right\|'''Optional: LED~~-Anzeigen für aktive Zugriegel-Sätze~~''']]		[[Datei:Legacy_LED_indicators.png\|300px\|thumb\|right\|'''Optional LED indicators for active drawbar sets''']]

	Vibrato/chorus V1 to C3 is selected by a rotary switch connected to '''PL33'''. The switch position is always polled unless Panel16 is configured with V1..3/Chorus buttons (''System Inits'' parameter #1504, also see note below). PL33 also carries switching signals, indicating rotary operation. You may connect indicator LEDs with serial resistor (330R and up) as shown below.		Vibrato/chorus V1 to C3 is selected by a rotary switch connected to '''PL33'''. The switch position is always polled unless Panel16 is configured with V1..3/Chorus buttons (''System Inits'' parameter #1504, also see note below). PL33 also carries switching signals, indicating rotary operation. You may connect indicator LEDs with serial resistor (330R and up) as shown below.

Bovist: /* Vibrato Knob (Rotary Switch) */

2025-10-26T08:59:13Z

Vibrato Knob (Rotary Switch)

← Nächstältere Version		Version vom 26. Oktober 2025, 08:59 Uhr
Zeile 618:		Zeile 618:
	[[Datei:Legacy_LED_indicators.png\|300px\|thumb\|right\|'''Optional: LED-Anzeigen für aktive Zugriegel-Sätze''']]		[[Datei:Legacy_LED_indicators.png\|300px\|thumb\|right\|'''Optional: LED-Anzeigen für aktive Zugriegel-Sätze''']]

	Vibrato/chorus V1 to C3 is selected by a rotary switch connected to '''PL33'''. The switch position is always polled unless Panel16 is configured with V1..3/Chorus buttons (''System Inits'' parameter #1504, also see note below). PL33 also carries switching signals, indicating rotary operation. You may connect ~~a LED~~ with serial resistor (330R and up) ~~here, cathode (-) connected to Common Gnd~~.		Vibrato/chorus V1 to C3 is selected by a rotary switch connected to '''PL33'''. The switch position is always polled unless Panel16 is configured with V1..3/Chorus buttons (''System Inits'' parameter #1504, also see note below). PL33 also carries switching signals, indicating rotary operation. You may connect indicator LEDs with serial resistor (330R and up) as shown below.

	Pinout PL33 VIBSW Vibrato rotary switch (active low – switch to Gnd):		Pinout PL33 VIBSW Vibrato rotary switch (active low – switch to Gnd):

Bovist: /* Vibrato Knob (Rotary Switch) */

2025-10-26T08:58:20Z

Vibrato Knob (Rotary Switch)

← Nächstältere Version		Version vom 26. Oktober 2025, 08:58 Uhr
Zeile 616:		Zeile 616:

	[[Datei:Hoax_rotary.png\|300px\|thumb\|right\|'''Vibrato rotary switch connection to PL33 VIBSW. Disregard "PL5" lettering in schematic. First contact lug of rotary switch is not used!''']]		[[Datei:Hoax_rotary.png\|300px\|thumb\|right\|'''Vibrato rotary switch connection to PL33 VIBSW. Disregard "PL5" lettering in schematic. First contact lug of rotary switch is not used!''']]
			[[Datei:Legacy_LED_indicators.png\|300px\|thumb\|right\|'''Optional: LED-Anzeigen für aktive Zugriegel-Sätze''']]

	Vibrato/chorus V1 to C3 is selected by a rotary switch connected to '''PL33'''. The switch position is always polled unless Panel16 is configured with V1..3/Chorus buttons (''System Inits'' parameter #1504, also see note below). PL33 also carries switching signals, indicating rotary operation. You may connect a LED with serial resistor (330R and up) here, cathode (-) connected to Common Gnd.		Vibrato/chorus V1 to C3 is selected by a rotary switch connected to '''PL33'''. The switch position is always polled unless Panel16 is configured with V1..3/Chorus buttons (''System Inits'' parameter #1504, also see note below). PL33 also carries switching signals, indicating rotary operation. You may connect a LED with serial resistor (330R and up) here, cathode (-) connected to Common Gnd.
Zeile 646:		Zeile 647:
	\|-		\|-
	!7		!7
	\|~~Rotary Slow Indicator~~ (~~active high~~)		\|Upper A/B select '''Output''' (High = Secondary DB set)
	\|-		\|-
	!8		!8
	\|~~Rotary Fast Indicator~~ (~~active high~~)		\|Lower A/B select '''Output''' (High = Secondary DB set)
	\|-		\|-
	!9		!9

Bovist: /* Connectors and Jumpers */

2025-01-06T11:18:06Z

Connectors and Jumpers

← Nächstältere Version		Version vom 6. Januar 2025, 11:18 Uhr
Zeile 25:		Zeile 25:

	[[Datei:HX36_mainboard_vert_1.png\|480px\|thumb\|right\|HX3.6 Components/Connector placement (also avalable as PDF, see [http://keyboardpartner.remotewebaccess.com/Files/index.php on our '''Documentation and Update Server'''])]]		[[Datei:HX36_mainboard_vert_1.png\|480px\|thumb\|right\|HX3.6 Components/Connector placement (also avalable as PDF, see [http://keyboardpartner.remotewebaccess.com/Files/index.php on our '''Documentation and Update Server'''])]]

			HX3.6 offers a wide range of connection options for universal use. Don't let this confuse you, for basic operation it is sufficient to connect the power supply and, if necessary, the MenuPanel to '''PANEL I2C'''. Unused connections can simply be left open. Max. cable length for Fatar scan board is 50cm, for other scan boards 1.5m. Max. cable length for I2C and MPX bus including all segments as well as onboard button and drawbar inputs is 1m. Keep cables as short as possible.

	{\|class="wikitable" border="1" cellpadding="4" cellspacing="0" style="text-align:left;width: 40%;background-color:#F8F8F8;"		{\|class="wikitable" border="1" cellpadding="4" cellspacing="0" style="text-align:left;width: 40%;background-color:#F8F8F8;"

Bovist: /* Panel16 */

2025-01-03T12:30:36Z

Panel16

← Nächstältere Version		Version vom 3. Januar 2025, 12:30 Uhr
Zeile 569:		Zeile 569:

	Panel16 has 4 "Common Preset" keys in the layout for standard organ installations. The "Common Preset" keys are binary coded so that more than one preset key can be active (pressed simultaneously). This allows 16 key combinations (all off to all on) corresponding to Common Presets 0 (live) to 15. Alternatively, these keys can be used to select V1-V3 vibrato or C1-C3 chorus depth. In this case, the Vibrato rotary switch on PL24 is omitted; then set ''System Inits'' parameter #1497 to 2.		Panel16 has 4 "Common Preset" keys in the layout for standard organ installations. The "Common Preset" keys are binary coded so that more than one preset key can be active (pressed simultaneously). This allows 16 key combinations (all off to all on) corresponding to Common Presets 0 (live) to 15. Alternatively, these keys can be used to select V1-V3 vibrato or C1-C3 chorus depth. In this case, the Vibrato rotary switch on PL24 is omitted; then set ''System Inits'' parameter #1497 to 2.


	{\|class="wikitable" border="1" cellpadding="4" cellspacing="0" style="text-align:center;width: 63%;background-color:#ffffcc;"		{\|class="wikitable" border="1" cellpadding="4" cellspacing="0" style="text-align:center;width: 63%;background-color:#ffffcc;"

Bovist: /* Panel16 */

2025-01-03T12:30:27Z

Panel16

← Nächstältere Version		Version vom 3. Januar 2025, 12:30 Uhr
Zeile 610:		Zeile 610:
	\|}		\|}



	~~<br>~~
	Buttons used for Common Presets, Drawbar Voices or V1..V3 V/C may be remapped deliberately to any digital input using the ''Switch Remap'' table in the HX3 Editor application.		Buttons used for Common Presets, Drawbar Voices or V1..V3 V/C may be remapped deliberately to any digital input using the ''Switch Remap'' table in the HX3 Editor application.

Bovist: /* External Buttons or Switches (I2C Bus) */

2025-01-03T09:38:46Z

External Buttons or Switches (I2C Bus)

@@ Zeile 666: / Zeile 666: @@
 ==External Buttons or Switches (I2C Bus)==
-===Board Adresses for Digital Inputs===
+====See '''[[I2C Bus]]''' page for details on external digital inputs.====
 ==Connecting Keyboard Scan Board(s)==

Bovist: /* Serial USB cable */

2025-01-02T14:22:06Z

Serial USB cable

← Nächstältere Version		Version vom 2. Januar 2025, 14:22 Uhr
Zeile 183:		Zeile 183:
	[[Datei:ftdi.jpg\|300px\|thumb\|right\|'''FTDI cable connected to HX3''']]		[[Datei:ftdi.jpg\|300px\|thumb\|right\|'''FTDI cable connected to HX3''']]

	For board configuration you may use a serial connection through FTDI USB adaptor cable or USB interface connected to ~~PL28~~ (cable colors imprinted). This port ist mostly used for factory programming and not needed for customer use. We recommend using the USB port MIDI interface. See '''[http://updates.keyboardpartner.de/Files/Manuals%20%28Anleitungen%29/UserManual_HX3_Manager.pdf HX3 Manager User Manual, printable PDF file]''' for details.		For board configuration you may use a serial connection through FTDI USB adaptor cable or USB interface connected to PL19 (cable colors imprinted). This port ist mostly used for factory programming and not needed for customer use. We recommend using the USB port MIDI interface. See '''[http://updates.keyboardpartner.de/Files/Manuals%20%28Anleitungen%29/UserManual_HX3_Manager.pdf HX3 Manager User Manual, printable PDF file]''' for details.

	=== Configuration by SD Card ===		=== Configuration by SD Card ===