Using HX3 with MIDI controllers: Unterschied zwischen den Versionen

Aus KeyboardPartner Wiki
Zur Navigation springenZur Suche springen
Zeile 1.189: Zeile 1.189:
HX3.5/KBP set supports MIDI channels for upper manual, lower manual and bass pedal. This MIDI CC set has been designed for use with the TouchOSC app.
HX3.5/KBP set supports MIDI channels for upper manual, lower manual and bass pedal. This MIDI CC set has been designed for use with the TouchOSC app.


Please note: In addition to MIDI base channel, base channel+1, and base channel+2, the HX3.5/KBP set uses base channel+3 for specific TouchOSC commands. Avoid assigning base channel+3 to other instruments.  
'''Please note''': In addition to MIDI base channel, base channel+1, and base channel+2, the HX3.5/KBP set uses base channel+3 for specific TouchOSC commands. Avoid assigning base channel+3 to other instruments.  


'''[https://updates.keyboardpartner.de/Files/Manuals%20%28Anleitungen%29/MIDI_Touchpad_CCs_560x.pdf HX3.5/KBP MIDI CC Set documentation, printable PDF file]'''<br>  
'''[https://updates.keyboardpartner.de/Files/Manuals%20%28Anleitungen%29/MIDI_Touchpad_CCs_560x.pdf HX3.5/KBP MIDI CC Set documentation, printable PDF file]'''<br>  

Version vom 19. Mai 2020, 16:19 Uhr

MIDI Control

HX3 accepts MIDI key on/off events (default: channel 1 to upper manual, 2 to lower manual, channel 3 to bass pedals) as well as various MIDI CCs with selectable compatibility sets. MIDI dynamics slightly affect key click noise. SysEx data other than its own are always ignored. Both MIDI jacks act as MIDI inputs with equal priority (default). The second MIDI jack may be jumpered as MIDI Out. (Details for HX3 mk4 see [HX3 mk4_Changes], for HX35 see [MIDI Configuration]).

You may connect two MIDI keyboards or controllers at the same time. Connecting a third MIDI device requires a MIDI Merge Interface. All HX3 functions that are relevant for the organ player may be remote-controlled by MIDI commands.

General

Connect MIDI Out of your MIDI controller/keyboard to one of the two HX3 MIDI inputs. Since MIDI is a one-way interface, HX3 cannot determine the setting of any MIDI controller value until you touch/use it once. By default all HX3 controllers are OFF. Do not use any controller button or drawbar unless HX3 is ready to accept data (drawbar/preset menu displayed). It is a good idea to power up HX3 before your MIDI master keyboard or master controller.

HX3.5 supports MIDI over USB through its USB port connected to a USB host, typically a PC. The USB connection is also suitable for controlling HX3.5 by the HX35 Editor application, firmware updates via MIDI SysEx, and DSP updates via DFU data transfer.

MIDI CC #7 (default, CC number variable) controls master volume. MIDI CC #11 (default, CC number variable) controls swell pedal/expression if no expression pedal connected to HX3. If you use your HX3-attached swell pedal, any MIDI expression message will be overwritten. If the attached swell pedal is not actuated, MIDI expression messages are accepted.

Note: Some MIDI controllers as well as organ keyboards (like Hammond XK and SK series) allow 2nd and 3rd harmonic percussion ON at the same time. In this case HX3 implementation regards "2nd ON" as "Percussion ON" tab. See Menu Panel section to select the desired MIDI CC set. Factory default is Native Instruments B4, which provides the most versatile command set.

MenuDisplay and HX3 Remote (HX3.4) or HX35 Editor (HX3.5 only) allow setup of MIDI Channel as well as MIDI CC set. Step down to MIDI menu section to alter settings. On the Menu Panel, press encoder knob for 2 seconds to save to power-up defaults.

  • MIDI Channel - sets MIDI base send/receive channel 1 to 10 (upper manual, lower manual is on +1, pedals on +2).
  • MIDI Option (HX3.4) - sets MIDI routing behaviour to
    • 'ReceiveThru' (MIDI OUT is THRU),
    • 'ReceiveSend' (MIDI received, only own MIDI key events to MIDI OUT),
    • 'RcvSendMerge'(MIDI received, own MIDI key events and incoming MIDI events merged to MIDI OUT) and
    • 'RcvSndMgNoCC' (as before, but MIDI CC commands discarded). On expander module, only valid setting is 'ReceiveThru'.
  • MIDI Option (HX3.5) - sets MIDI routing behaviour to
    • 'Local Tx' (MIDI OUT sends own keyboard data),
    • 'Inp 1 Thru' (MIDI IN1 routed to MIDI OUT and MIDI OUT over USB),
    • 'Inp 2 Thru' (MIDI IN2 routed to MIDI OUT) and
    • 'USB InThru' (MIDI IN over USB routed to MIDI OUT).
  • MIDI CC Set - sets recognized MIDI CC set to
    • 'NI B4' Native Instruments B4 (default),
    • 'Voce' MIDI drawbars,
    • 'Hamichord' (or 'Mojo', same hardware),
    • 'Hammond XK',
    • 'Hammond SK' (Note: Hammond changed MIDI CC set between XK and SK series, please try out which one fits),
    • 'KeyB Duo',
    • 'Boehm Sempra! (HX3.5 only),
    • 'Nord C1/C2' (HX3.5 only),
    • 'Custom' (HX3 mk4 only, to be set by HX3 Remote)

HX3.4 Generated MIDI Events

HX3.4 (mk2/3/4 board) is transmitting local keyboard ON/OFF events on MIDI base channel (upper), MIDI base channel +1 (lower) and MIDI base channel +2 (pedal). It sends MIDI CCs of user controls (drawbars, tabs) according to NI B4 implementation (independently of selected CC set). From firmware 3.82 and up, HX3 will not send own MIDI CCs on MIDI OUT when MIDI Option = 3 (RcvSndMgNoCC). MIDI Option = 3 is now default on all firmwares except HX3 Expander (which has to accept MIDI CCs). This change has been made since MIDI CCs sended by HX3 may disturb MIDI workstations/arrangers. Note: If send/receive of MIDI CCs is enabled (Option = 1 or 2), HX3 will transmit its own CCs.

HX3.5 Generated MIDI Events

HX3.5 is transmitting local keyboard ON/OFF events on MIDI base channel (upper), MIDI base channel +1 (lower) and MIDI base channel +2 (pedal). It sends MIDI Program Change and Swell Pedal, but no other user control data. MIDI IN1, IN2 and MIDI over USB are always accepted. Important: MIDI IN2 and MIDI IN over USB may not be used simultaneously.

For OEM only: Independent from MIDI option selected, HX3 will always send a 3.3V TTL level MIDI signal on PL16 pin 8 for controlling Ventilator/Minivent DSP board with synced stop/slow/fast. Pin 34 of Vent DSP board is MIDI TTL input. Also wire digital ground (PL16 pin 10). Ventilator DSP accepts MIDI CC #21 values 0 (stop), 1 (slow), 2 (fast) on channel 1.

There is no way to save an upper or lower preset/program remotely; you have to use the MenuPanel’s Save function.

Program Change

Program Change on HX3.4

HX3 mk4 will accept MIDI Program Change Commands in some MIDI CC sets. In NI B4 mode, MIDI program changes 12..23 on upper manual channel will set lower manual voice according to common NI B4 hardware controllers. In Hammond CC modes, program 11 is the "live" preset (inverse "B" key) and will recall voice 0.

Program Change on HX3.5

In general, HX3.5 (firmware 5.3 and up) will handle MIDI Program Change Commands (valid numbers range from 0 to 39). Numbers 0 to 15 will be handled as "Set Drawbar Voice" for upper, lower and pedal MIDI channel separately, i.e. it resembles the "inverse" preset keys found on Hammond console organs. Numbers 16 to 39 will select GM voices as preallocated via the HX35 Editor. Drawbar Voice changes will not affect Tab settings (Percussion, Vibrato etc) in any way.

However, not all HX3.5 MIDI CC sets are handling MIDI program changes in the same way: In NI B4 mode, MIDI program changes 12..23 on upper manual channel will set lower manual voice complying with common NI B4 hardware controllers. In Hammond CC modes, program 11 is the "live" preset (inverse "B" key) and will recall voice 0. In Nord C1/C2 CC mode, program 126/127 are "live" presets (inverse "A#" and "B" key) and will recall voice 0.

Bank Select on HX3.5

HX3.5 will handle MIDI Bank Select Commands as "Set Overall Preset" (valid numbers range from 0 to 15 or 0 to 99 from FW #5.516 on) per default. Overall Presets include all Tab settings and additional pots (volume, reverb amount etc) as well as the drawbar settings. Note that some MIDI keyboards will send a MIDI Bank Select command separately, others will issue a MIDI Bank Select only with a MIDI Program Change. In the latter case, the issued MIDI Program Change command will override the voice setting.

Please note: firmwares #5.500 to #5.515 contained a bug that prevented Commom Preset selects.

From HX3.5 FW #5.516, Common Presets 0..99 are selected in all CC Sets by Bank Select command (LSB, CC #32 decimal). All three channels are valid.

From HX3.5 FW #5.526: Common Presets 0..99 are selected in all CC Sets by arbitrary CC command (Default: #32 dez. = Bank Select LSB), selectable in MIDI menu.

MIDI CC Sets

HX3 provides several pre-configured MIDI CC sets plus one fully customizable set (HX3.4 only), selectable by MenuPanel, by HX3 Remote or HX35 Editor application, respectively. Factory default is the Native Instruments B4 set, supported by many MIDI controllers. If MIDI CC output is enabled, HX3 will send CCs always according to NI B4 set. HX3 does not support weird SysEx encodings found on some Roland, Oberheim and Viscount models. All values based decimal!

A very comprehensive Böhm/Keyswerk Sempra MIDI CC set is available on HX3.5 mainboards.

NI B4 d3c

The Doepfer d3c drawbar controller is a very nice and rugged piece of gear, so we recommend it for use with our HX3 board. It does support foot controllers and foot switches. The Keyswerk/Böhm db4 is also compatible with NI B4 CC set.

Upper, lower and bass drawbars work as usual. It is a good idea to set all to zero before switching on as this is a “known state” for HX3. Also the Percussion and Vibrato buttons work as described in d3c manual. There is a small drawback, anyway: Default HX3 Vibrato setting is V1 (but upper/lower vibrato OFF), while the V1 LED will not light up when powering up the d3c (there is no “V0” on a real Hammond!). So pressing the V1 button will not change the sound – just turn its LED on.

The “Brightness” knob controls AO28 “tone” parameter of the HX3. There is no key click simulated by HX3 (it is just there), so there is no key click adjustment button. The “Key Click” knob controls the bass sustain instead.

Do not use the “Harmonic content” knob as it sends the “Percussion” button’s controller number like a continuous controller. What for? No idea. This is definitely of no use.

Preset buttons may be used, but in a restricted way. First, HX3 has 15 presets per manual, not 127 like NI B4. When selecting “Bank 1”, all 12 available preset buttons work on upper manual. When selecting “Bank 2”, all 12 preset buttons work on lower manual. Doepfer d3c resends the program change message when changing the bank, which may be annoying. Choose bank 2, lower preset first, then bank 1, upper preset. BTW: Bank buttons do not send bank select messages, they just add an offset to the preset buttons. Blame Doepfer for that.

Doepfer d3c preset 1 is the HX3 “Live” (preset 0) position. It will be saved temporarily (until HX3 is switched off) when a preset sound (2 to 12) is selected. If you return to preset 1 “Live”, your last drawbar/button setting will be recalled. Please note: HX3 tracks drawbar and button changes even when in preset position 2 to 12, so it keeps itself updated all the time.

NI B4 set accepts program changes for upper manual MIDI channel, range 0..11 = upper presets and 12..23 = lower presets.


Channel CC# Type Function Remarks
1 1 Switch Rotary Slow/Fast Modulation Wheel
1 7 Slider Master Volume was "122 Amp volume" on older firmwares
1 11 Slider Swell Pedal
1 12..20 Slider Upper Drawbars
1 21..29 Slider Lower Drawbars
1 30 Switch Vibr Lower ON
1 31 Switch Vibr Upper ON
1 33 Slider Bass DB 16
1 34 Slider Bass DB 8
1 66 Switch Percussion ON
1 68 Switch Rotary RUN "Rotary On/Off" on B4
1 70 Switch Percussion SOFT inverted!
1 71 Switch Percussion FAST inverted!
1 72 Switch Percussion THIRD
1 73 Fixed Vibr Mix Chorus if < 96
1 74 Fixed Vibr Amount 0..55 = V1, 56..87 = V2, 88..127 = V3
1 75 Slider Bass Pedal Sustain "Key Click" on B4
1 76 Slider Tube Amp Gain "Tube Amp Drive" on B4
1 78 Slider Swell Trim Cap "Tube Amp Body" on B4
1 79 Slider Tone "Tube Amp Brightness" on B4
1 84 Fixed Reverb 0..23 = OFF, 24..47 = Rev 1, 48..63 = Rev 2, 64..127 = Rev 3
2 12..20 Slider Lower Drawbars Same as 21..29 on Channel 1
2 30, 31 Switch Vibr Lower ON Same as 30 on Channel 1


Voce Drawbars

Using your HX3 board with Voce MIDI Drawbars is straightforward, as the Voce module sends on one MIDI channel only (i.e. upper manual). Please note that Voce MIDI Drawbars does not send drawbar data unless you press the “Drawbar/Save” button, so that its LED lights up. You may change the Voce MIDI Drawbars send channel (back rotary HEX switch) at any time to lower (2) and bass channel (3), although this is somewhat inconvenient. In case of your technician has installed a toggle switch on the back side, channels can be changed easily.

Voce CC set accepts program changes for upper and lower manual on separate MIDI channels, range 0..15.


Channel CC# Type HX3 Function Remarks
1 7 Slider Master Volume
1 11 Slider Swell Pedal
1 12..20 Slider Upper Drawbars
1 21..29 Slider Lower Drawbars
1, 2 68 Switch Rotary Slow/Fast
1, 2 70 Switch Percussion SOFT
1, 2 71 Switch Percussion FAST
1, 2 72 Switch Percussion THIRD
1, 2 73 Switch Percussion ON
1, 2 87, 89 Slider Tone "Treble" on Voce
1, 2 88 Slider Swell Trim Cap "Bass" on Voce
1, 2 90 Slider Reverb "Hum" on Voce, 0..23 = OFF, 24..47 = Rev 1, 48..63 = Rev 2, 64..127 = Rev 3
1, 2 91 Slider Amp 122 Volume "Distortion" on Voce, same as CC #7
1, 2 92 Switch Rotary Stop/Run
1, 2 93 Fixed Vibrato Knob 0..23 = V1, 24..42 = V2, 43..64 = V3, 65..90 = C1, 91..110 = C2, 111..127 = C3
1 95 Switch Vibr Upper ON
2 12..20 Slider Lower Drawbars Same as 21..29 on Channel 1
2 95 Switch Vibr Lower ON
3 12 Slider Bass DB 16
3 13 Slider Bass DB 5 1/3
3 14 Slider Bass DB 8
3 15 Slider Bass Pedal Sustain


Hamichord/Mojo

Italian Hamichord/Mojo controller set supports only base MIDI channel. Key ON/OFF data of channel 2 (lower) and 3 (pedals) will be accepted, though.

Hamichord/Mojo CC set will not accept Program Change messages since Hamichord/Mojo always sends a "snapshot" of all MIDI CCs when changing a preset.


Channel CC# Type Function Remarks
1 1 Fixed Rotary Slow/Fast Modulation Wheel, 0..30 = SLOW, 31..94 = STOP, 95..127 = FAST
1 7 Slider Amp 122 Volume
1 11 Slider Swell Pedal
1 12..20 Slider Upper Drawbars
1 21..29 Slider Lower Drawbars
1 30 Slider Pedal DDB 16
1 31 Slider Pedal DDB 8
1 32 Fixed Vibr Knob 0..21 = V1, 22..43 = C1, 44..65 = V2, 66..87 = C2, 88..109 = V3, 110..127 = C3
1 34 Slider Swell Pedal same as #11
1 35 Slider Amp 122 Volume same as #7, "Tube Amp Drive" on Hamichord/Mojo
1 38 Slider Bass Pedal Sustain "Keyclick" on Hamichord/Mojo
1 39 Fixed Reverb 0..23 = OFF, 24..47 = Rev 1, 48..63 = Rev 2, 64..127 = Rev 3
1 42 Switch Percussion ON
1 43 Switch Percussion SOFT inverted!
1 44 Switch Percussion FAST inverted!
1 45 Switch Percussion THIRD
1 46 Switch Vibr Upper ON
1 47 Switch Vibr Lower ON
1 48 Switch Rotary RUN
1 47 Switch Rotary SLOW/FAST
1 54 Switch Audio Config A/B "L/R out select" on Mojo
1 91 Fixed TG Leakage "Crosstalk" on Mojo
1 92 Fixed TG Cap Set "Keyclick length" on Mojo
1 95 Slider Swell Trim Cap "Percussion Volume" on Mojo


Hammond XK

HX3 supports most of Hammond XK MIDI controller functions. For convenience, some controllers have been relocated to other HX3 functions:

  • XK Overdrive knob controls HX3 Rotary Tube Amp Volume
  • XK Reverb button controls HX3 lower manual Vibrato On
  • XK Tube On button controls HX3 Reverb

Hammond uses NRPN controllers instead of standard controller range. Drawbars are encoded through a weird grid scheme using only 3 CC#s, see XK manual for details.

Hammond XK set accepts program changes for upper manual and lower manual MIDI channel, range 0..15. Hammond Preset 11 will be converted to HX3 preset 0 (live).


Channel CC# Type Function Remarks
1,2,3 6 Value NRPN data entry
1,2,3 7 Slider Master Volume
1,2,3 11 Slider Swell Pedal
1,2,3 80 Fixed Upper drawbars According to Hammond encoding, see XK user manual
1,2,3 81 Fixed Lower drawbars According to Hammond encoding, see XK user manual
1,2,3 82 Fixed Pedal drawbars According to Hammond encoding, see XK user manual
1,2,3 95 Don't Care Save Upper If received, saves upper drawbars and setup to current preset#
1,2,3 96 Don't Care Save Lower If received, saves lower drawbars and setup to current preset#
1,2,3 98 Value LSB of NRPN controller#
1,2,3 99 Value MSB of NRPN controller#


Hammond XK NRPN Encoding is as follows (NRPN represented as hexadecimal values):

NRPN # XK Function HX3 Function/Remarks
00,0A EQ Bass Gain Swell Trim (!)
02,0A EQ Treble Gain TONE pot (!)
02,09 Vib Upper ON (same)
17,09 Vib Lower ON (same)
04,0A Reverb ON Vib Lower ON (!)
03,09 Vib Knob 0=V1, 1=V2, 2=V3, 3=C1, 4=C2, 5=C3
00,09 Leslie Run (same)
01,09 Leslie Fast (same)
05,09 Overdrive Tube Amp Gain
00,08 Perc ON (same)
01,08 Perc THIRD (same)
02,08 Perc FAST (same)
03,08 Perc SOFT (same)
09,09 Tube ON Reverb ON (!)
07,02 User Switch Audio Config A/B (!)
01,07 Manual Bass Key Split ON (!)
00,07 Split Key Split ON


Hammond SK

Hammond SK does not use the weird drawbar encoding scheme of the XK, instead standard CCs whith same numbers as NI B4 CCs for upper/lower manual and bass pedal 16'/8'. For other controllers, knobs and buttons, the SK uses nearly the NRPN scheme as found on XK. Some NRPNs differ, though (see table).

Hammond SK set accepts program changes for upper manual and lower manual MIDI channel, range 0..15. Hammond Preset 11 will be converted to HX3 preset 0 (live).


Channel CC# Type Function Remarks
1,2,3 6 Value NRPN data entry
1,2,3 7 Slider Master Volume
1,2,3 11 Slider Swell Pedal
1,2,3 12..20 Slider Upper Drawbars similar to NI B4 scheme
1,2,3 21..29 Slider Lower Drawbars similar to NI B4 scheme
1,2,3 33 Slider Bass DB 16 similar to NI B4 scheme
1,2,3 34 Slider Bass DB 8 similar to NI B4 scheme
1,2,3 98 Value LSB of NRPN controller#
1,2,3 99 Value MSB of NRPN controller#


Hammond SK NRPN Encoding is as follows (NRPN represented as hexadecimal values):

NRPN # XK Function HX3 Function/Remarks
00,0A EQ Bass Gain Swell Trim (!)
02,0A EQ Treble Gain TONE pot (!)
02,09 Vib Upper ON (same)
03,09 Vib Lower ON (same)
04,0A Reverb ON Vib Lower ON (!)
03,09 Vib Knob 0=V1, 1=V2, 2=V3, 3=C1, 4=C2, 5=C3
07,09 Leslie Stop (inverted Run!)
01,09 Leslie Fast (same)
00,30 Overdrive ON ignored (!)
02,30 Overdrive Tube Amp Gain
00,08 Perc ON (same)
01,08 Perc THIRD (same)
02,08 Perc FAST (same)
03,08 Perc SOFT (same)
02,22 Sustain ON Bass Sustain ON (!)
09,09 Tube ON Reverb ON (!)
07,02 User Switch Audio Config A/B (!)
00,07 Manual Bass Key Split ON (!)


KeyB Duo

Italian KeyB/Diversi controller set supports three MIDI channels.

KeyB set accepts program changes for upper and lower manual on separate MIDI channels, range 0..15.


Channel CC# Type Function Remarks
1 7 Slider Master Volume
1 9 Fixed Reverb 0..3 0..23 = OFF, 24..47 = Rev 1, 48..63 = Rev 2, 64..127 = Rev 3
1 11 Slider Swell Pedal
1 12..20 Slider Upper Drawbars
1 21..29 Slider Lower Drawbars
1 68 Fixed Rotary Slow/Fast 0 = SLOW, 64 = STOP, 127 = FAST
1 70 Switch Percussion FAST
1 71 Switch Percussion SOFT
1 72 Switch Percussion THIRD
1 73 Switch Percussion ON
1 79 Switch Split ON "String Bass" on KeyB
1 89 Slider Percussion Level "Key Click" on KeyB
1 90 Fixed Leakage "Crosstalk" on KeyB, scaled to 0..3
1 91 Slider Amp 122 Volume "Tube Amp Drive" on KeyB
1 95 Switch Vibrato Upper ON
1 93 Fixed Vibrato Knob 18 = V1, 79 = C1, 36 = V2, 100 = C2, 58 = V3, 122 = C3
1 103 Slider Swell Trim Cap "Bass Equ" on KeyB
1 104 Slider Tone "Treble Equ" on KeyB
1 105 Slider Pedal Sustain
1 106 Switch Audio Config A/B "Volume Soft" on KeyB
2 12..20 Slider Lower Drawbars Same as 21..29 on Channel 1
2 95 Switch Vibr Lower ON
3 12 Slider Bass DB 16
3 13 Slider Bass DB 8


MIDI Custom CC

(Not yet available on HX3.5)

FW #3.6x and up provide a "custom MIDI CC" set which may be altered to your needs by using HX3 Remote application (HX3.4 only). By factory default, it is set to accept Nord C2 MIDI data (also compatible with Ocean Beach DB-1 controller). See wiki page HX3_Remote_Application#Editing_MIDI_Custom_CCs how to create a custom CC set and store it to HX3. Please note that currently the custom MIDI CC set only accepts controller commands on upper manual MIDI channel (1 on factory default).


Nord C1/C2 MIDI CC Set

(Only available on HX3.5)

Nord C1/C2 set supports MIDI channels for upper manual, lower manual and bass pedal.

Channel CC# Type Function Remarks
1 4 Slider Swell Pedal
1 111 Slider Tube Amp Gain
1 113 Slider Hi Equ HX3 Tone Pot
1 102 Slider Reverb Amount
1 96 Switch Reverb Type 0 = Off, 1 = Rev I, 2 = Rev II, 3 = Rev I+II
1 97 Switch Reverb On/Off
1 16..24 Slider Upper Drawbars
2 16..24 Slider Lower Drawbars
3 16..17 Slider Pedal Drawbars
3 18 Slider Pedal Pluck
3 19 Slider Pedal Release Sustain length
1 87 Switch Percussion ON
1 27 Switch Percussion FAST
1 28 Switch Percussion SOFT inverted!
1 95 Switch Percussion THIRD
1 91 Slider Amp 122 Volume "Tube Amp Drive" on KeyB
1 85 Switch Vibrato Upper ON
2 85 Switch Vibr Lower ON
1 84 Fixed Vibrato Knob 18 = V1, 79 = C1, 36 = V2, 100 = C2, 58 = V3, 122 = C3


Versatile MIDI CC Set

(Only available on HX3.5)

Versatile set supports MIDI channels for upper manual, lower manual and bass pedal.

HX3.5 Versatile MIDI CC Set documentation, printable PDF file


HX3.5/KBP MIDI CC Set

(Only available on HX3.5)

HX3.5/KBP set supports MIDI channels for upper manual, lower manual and bass pedal. This MIDI CC set has been designed for use with the TouchOSC app.

Please note: In addition to MIDI base channel, base channel+1, and base channel+2, the HX3.5/KBP set uses base channel+3 for specific TouchOSC commands. Avoid assigning base channel+3 to other instruments.

HX3.5/KBP MIDI CC Set documentation, printable PDF file


Additional Info

Firmware #3.6x and FPGA #20072014 or newer provide a secondary MIDI input (merged with other) and also send MIDI CCs according to NI B4 from all local controllers (drawbars/buttons/switches).