HX3.5 DSP Updates: Unterschied zwischen den Versionen

Aus KeyboardPartner Wiki
Zur Navigation springenZur Suche springen
KKeine Bearbeitungszusammenfassung
(9 dazwischenliegende Versionen desselben Benutzers werden nicht angezeigt)
Zeile 1: Zeile 1:
[[Datei:dsp_update.png|400px|thumb|right|'''HX3 DSP Update Application''']]
'''Preliminary'''
'''Preliminary'''


While organ sound generation is done entirely in hardware (FPGA), the HX3.5 board uses an additional Digital Signal Processor (DSP) for reverb effects (EFX) and General MIDI voice generation. With an extended HX3 licence, 128 GM sounds are installed as a so-called soundbank. Up to two soundbanks can be installed at a time; a second soundbank may contain additional, more sophisticated instruments (with same MIDI GM bank and program numbers) which replace the instruments in first soundbank.
While organ sound generation is done entirely in hardware (FPGA), the HX3.5 board uses an additional Digital Signal Processor (DSP) for reverb effects (EFX) and General MIDI voice generation. 128 GM sounds are installed as a so-called soundbank. Up to two soundbanks can be installed at a time; with an extended HX3 licence, a second soundbank may contain additional, more sophisticated instruments (with same MIDI GM bank and program numbers) which replace the instruments in first soundbank.


At this time, the DSP firmware and DSP soundbank(s) cannot be updated by SD Card; use USB connection to PL3 or HX3.5 instead. Please follow instructions below carefully.
At this time, the DSP firmware and DSP soundbank(s) cannot be updated by SD Card; use USB connection to PL3 or HX3.5 instead. Please follow instructions below carefully.


==Update by USB==
==Preparation==


In USB firmware/soundbank update mode, HX3.5 cancels the "MIDI over USB" mode and registers as a DFU-capable device. An updater application named "DreamDFU.exe" (Windows OS only) handles all further USB communication.
In USB firmware/soundbank update mode, HX3.5 cancels the "MIDI over USB" mode and registers as a DFU-capable device. An updater application named "DreamDFU.exe" (Windows OS only) handles all further USB communication.
* Attach FTDI serial cable to HX3.5 PL19
* Attach USB cable to HX3.5 Board. PC should recognize a USB MIDI device.
* Select FT232R cable connection in HX3.5 Editor. If successfull, HX3.5 Editor should read parameters and show actual values.
==Firmware Update by USB==


To update the DSP firmware, proceed as follows:  
To update the DSP firmware, proceed as follows:  


* Attach FTDI serial cable to HX3.5 PL19
* Open '''HX3.5 Editor's Update/Finalize window''' and click "Start DFU". Connected PC will deregister USB MIDI and recognize a DFU device instead.
* Attach USB cable to HX3.5 Board. PC should recognize a USB MIDI device.
* HX3.5 will show "DSP update (DFU)" on MenuPanel display.
* Connect with HX3.5 Editor to FT232R cable. If successfull, HX3.5 should read parameters and will show actual values.
* Start '''DreamDFU.exe''' and open DSP firmware file "HX35_5504-FW.dfu". '''DreamDFU.exe''' should show a window as seen in picture.
* Open HX3.5 Update/Finalize window and click "Start DFU". PC will deregister USB MIDI and recognize a DFU device instead.
* Click "Update Device". A progress bar will indicate the update progress.
* When finished, close DreamDFU.exe by clicking on "Abort" or Close button.
* HX3.5 will revert to MIDI over USB mode.
 
==Soundbank Installation/Update by USB==
 
To update/install the "Extended Licence" GM2 soundbank, proceed as follows:
 
* Open '''HX3.5 Editor's Update/Finalize window''' and click "Start DFU". Connected PC will deregister USB MIDI and recognize a DFU device instead.
* HX3.5 will show "DSP update (DFU)" on MenuPanel display.
* HX3.5 will show "DSP update (DFU)" on MenuPanel display.
* Start '''DreamDFU.exe''' and open soundbank or DSP (SAM5504) firmware file.
* Start '''DreamDFU.exe''' and open supplied DSP soundbank file, e.g. "Piano16_0x8050.dfu" or similar. '''DreamDFU.exe''' should show a window as seen in picture.
* Click "Update". A process bar will indicate update.
* Click "Update Device". A progress bar will indicate update process.
* Close DreamDFU.exe by clicking on "Abort" or Close button.
* HX3.5 will revert to MIDI over USB mode.

Version vom 17. Juli 2018, 14:46 Uhr

HX3 DSP Update Application

Preliminary

While organ sound generation is done entirely in hardware (FPGA), the HX3.5 board uses an additional Digital Signal Processor (DSP) for reverb effects (EFX) and General MIDI voice generation. 128 GM sounds are installed as a so-called soundbank. Up to two soundbanks can be installed at a time; with an extended HX3 licence, a second soundbank may contain additional, more sophisticated instruments (with same MIDI GM bank and program numbers) which replace the instruments in first soundbank.

At this time, the DSP firmware and DSP soundbank(s) cannot be updated by SD Card; use USB connection to PL3 or HX3.5 instead. Please follow instructions below carefully.

Preparation

In USB firmware/soundbank update mode, HX3.5 cancels the "MIDI over USB" mode and registers as a DFU-capable device. An updater application named "DreamDFU.exe" (Windows OS only) handles all further USB communication.

  • Attach FTDI serial cable to HX3.5 PL19
  • Attach USB cable to HX3.5 Board. PC should recognize a USB MIDI device.
  • Select FT232R cable connection in HX3.5 Editor. If successfull, HX3.5 Editor should read parameters and show actual values.

Firmware Update by USB

To update the DSP firmware, proceed as follows:

  • Open HX3.5 Editor's Update/Finalize window and click "Start DFU". Connected PC will deregister USB MIDI and recognize a DFU device instead.
  • HX3.5 will show "DSP update (DFU)" on MenuPanel display.
  • Start DreamDFU.exe and open DSP firmware file "HX35_5504-FW.dfu". DreamDFU.exe should show a window as seen in picture.
  • Click "Update Device". A progress bar will indicate the update progress.
  • When finished, close DreamDFU.exe by clicking on "Abort" or Close button.
  • HX3.5 will revert to MIDI over USB mode.

Soundbank Installation/Update by USB

To update/install the "Extended Licence" GM2 soundbank, proceed as follows:

  • Open HX3.5 Editor's Update/Finalize window and click "Start DFU". Connected PC will deregister USB MIDI and recognize a DFU device instead.
  • HX3.5 will show "DSP update (DFU)" on MenuPanel display.
  • Start DreamDFU.exe and open supplied DSP soundbank file, e.g. "Piano16_0x8050.dfu" or similar. DreamDFU.exe should show a window as seen in picture.
  • Click "Update Device". A progress bar will indicate update process.
  • Close DreamDFU.exe by clicking on "Abort" or Close button.
  • HX3.5 will revert to MIDI over USB mode.